Manual Frico Infraglas (page 4 of 8) (English)

787197

Zoom out

Zoom in

1/8

INFRAGLAS

IHG12/15/22 IP65

MONTAGE- UND GEBRAUCHSANWEISUNG

INSTRUCTIONS FOR USE

MODE D’EMPLOI

ISTRUZIONE PER L’USO

INSTRUCCIONES DE MONTAJE Y USO

MONTAGE- OG BRUGSANVISNING

MONTAGE- OCH BRUKSANVISNING

MONTERINGS- OG BRUKSANVISNING

ASENNUS- JA KÄYTTÖOHJE

Irrtum und technische Änderungen vorbehalten ・ Subject to errors and technical changes ・ Sous reserve d‘erreurs et de

modifications techniques ・Excepto erro ou alteracao tecnica ・Salvo error o modificacion tecnica ・Fejl og tekniske

ændringer forbeholdt ・Fel och tekniska ändringar reserverade ・Feil og tekniske endringer reservert ・Virheet ja tekniset

muutokset on varattu!

Main office: Frico AB, Industrivägen 41, SE-433 61 Sävedalen Sweden

Tel: +46 31 336 86 00 - mailbox@frico.se - www.frico.net

For latest updated information and information about your local contact: www.frico.net

ASSEMBLY AND OPERATING INSTRUCTIONS

Dear Customer,

please read the following information carefully before using

the appliance for the first time for your own safety and to

ensure correct use.

DESIGNATED USE:

Outdoor areas.

SAFETY INFORMATION:

•During use of this appliance, it is necessary to observe

some precautions. Improper operation with disregard of

precautions may result in infliction of harm to health of the

user and other people, as well as in infliction of damage to

their property.

•Use this appliance only as described in this manual. Any

other use is not recommended by the manufacturer and

may cause fire, electric shock or injury.

•Do not use appliance or any part of the appliance out of

the intended use to avoid risk.

•The manufacturer is not responsible for any damage that

could happen from improper use.

•The manufacturer emphasizes that this appliance should

be used in a responsible manner and that all procedures,

warnings, and safety instructions contained in this booklet

be followed strictly.

•Use only the voltage specified on the rating plate of this

appliance.

•Remove transit protection before use.

•Keep packaging materials out of reach of children.

•This appliance must be handled with care and avoid

vibration or hitting.

•Do not apply any pressure on the glass surface.

•In particularly, do not use the appliance in dusty areas or

where explosives are stored.

•Do not use the appliance in a building site, green house,

barn or in animal stables.

•Do not use this appliance in the place of animal

propagating and rising.

•Do not use the appliance as a sauna heater.

•This appliance is NOT intended to be installed in

wardrobes.

•Do not use this appliance on a wet surface, or where it

can fall or be pushed into water.

•Do not reach for an appliance that has fallen into water.

Switch off at supply and unplug immediately.

•Install and operate this appliance in strictly horizontal

position on the ceiling or ceiling structural surface. The

thermal resistance of the ceiling coating and ceiling

material should be at least 80 °C.

•WARNING: Check for damage to the appliance

regularly. The heater must not be used if the black

radiant panel or any other part of the heater is

damaged.

• Only connect the appliance to a properly installed socket-

outlet with earthing contact. Possibly a slow-blow C-fuse

is necessary if you experience problems by switching on to

overloaded fuses.

• Only connect the appliance to a.c. mains as specified on

the rating plate.

• Never touch live parts! Danger to life!

• Never operate the appliance with wet hands! Danger to

life!

• Do not store or use any flammable materials or sprays in

the vicinity of the appliance when the appliance is in use.

Fire hazard!

• Do not use the appliance in flammable atmospheres (e.g.

in the vicinity of combustible gases or spray cans)!

Explosion and fire hazard!

•Important! Do not insert any foreign objects into the

appliance openings! Risk of injury (electric shock) and

damage to the appliance!

• Attention! Do not look longer time into the light!

•Attention! The unit complete becomes very hot when

the appliance is in use! Place the appliance so that it

cannot be touched by accident. Risk of burns!

• No objects whatsoever such as garlands and streamers

should be fastened to the radiant heater. Risk of fire!

•Never attempt to adjust the pivoting angle when the

device is in operation! Risk of burns!

Allow the appliance to cool down before adjusting the

bracket

• The appliance is not intended for use by young children

or infirm persons without supervision! Young children

should be supervised to ensure that they do not play with

the appliance!

• The socket-outlet must be accessible at all times to

enable the mains plug to be disconnected as quickly as

possible!

• These instructions for use belong to the appliance and

must be kept in a safe place. When changing owners, these

instructions must be surrendered to the new owner!

• The appliance must be allowed to cool down before being

carried and stored!

LOCATION:

•If the radiant heater is equipped with or without a frame

for ceiling mounting it must be secured 2.1-2.3 meter

above the ground. The installation height for the 1.5kW

version is at least 1.8 m above the ground.

• If the radiant heater is equipped with or without a frame

for wall mounting it must be secured 2.1-2.3 meter above

the ground. The installation height for the 1.5kW version is

at least 1.8 m above the ground.

• The device may only be commissioned if it has been

mounted level.

• The distance between the heater and combustible

objects and other buildings must be at least 100 cm.

• Since the device emits radiant heat, make sure that no

items, such as furniture, are located between the device

and the persons or objects to be warmed!

POWER CORD:

•The use of an extension cord with this appliance is not

recommended.

• The power cord must not come into contact with

heated parts of the device!

• Never remove the plug from the socket by pulling on

the cord! Never move the device by pulling on the cord or

carry the device by the cord!

• Do not wind the cord around the device! Do not

operate the device with the cord wound up!

• Do not clamp the cord, or pull it over sharp edges!

• Do not run cord under carpeting, throw rugs or runners

etc. Arrange cord away from areas where it is likely to be

tripped over.

•Never use the appliance if the appliance or cord is

damaged. Risk of injury!

INSTALLATION:

• The device may only be installed and connected by

qualified professionals. The installation must be

isolated prior to commencing any electrical work!

Risk of fire!

• Sufficient air exchange for heat dissipation must

be ensured in the cavity above the radiant heater.

•Only commission the device after it has been fully

installed.

•This heater comes with a pair of stainless steel adjustable

angle mounting brackets. The adjustable angle enables the

heater to be installed on vertical, horizontal and inclined

surfaces.

WARNING:

Slight crackles may be heard during the heating or cooling

period. This is normal operational noise.

NOTE:

After switching on the appliance for the first time and

following extended periods on non-use, the appliance

may expel a slight odor for a short time. It will not affect

the use of the heater.

To exclude unpleasant burnt odor, it is recommended

to keep the heater clean preventing accumulation of

dust on it

The distance between the heater and the remote cont

rol should be less than 3 metre, and the remote contr

ol must be directly point to the receiver on the front p

anel during the operation.

CLEANING:

• First, disconnect the equipment from the power supply

system!

• After the appliance has cooled down, wipe off dust with a

damp soft rag in cold condition

•During operation, it is necessary to periodically (once a

year) check the electric cable contacts and terminal

connectors for good tightening.

• Do not use any abrasive or caustic cleaning agents!

• Never immerse the appliance in water! Danger to life!

AFTER-SALES SERVICE:

• All repairs must be referred to authorised personnel!

Therefore, you should contact your specialized dealer or

the customer service.

•Important! Any tampering with the appliance will

invalidate the warranty.

• Repairs carried out improperly and by unqualified persons

may have serious consequences for the user!

TECHNICAL DATA:

• Connection/fuse: 230-240V~50Hz with 10 Amp C (= slow-

blowing fuse) (IHGB/W12, IHGB/W15), with 16 Amp C (=

slow-blowing fuse) (IHGB/W22)

• Output: 1200 Watt, 1500 Watt and 2200 Watt

• Infrared tube: 1,2 kW= IHGB/W12, 1,5 kW= IHGB/W15,

2,2 kW= IHGB/W22,

• Guaranteed service life: up to 5000 hours with average

use

• Type of protection: IP65

• Weight IHGB/W12SR model: 3,6 kg

• Weight IHGB/W15S/R models: 5,1/5,2 kg

• Weight IHGB/W22S/R models: 5,1/5,2 kg

• Casing: Corrosion-resistance anodized aluminium

•Front: SCHOTT NEXTREMA® ceramic glass

•Cable: 1,80m 3-wire 1,5 mm², Schuko plug

OPERATING INSTRUCTION FOR IHGB/W12SR MODELS:

1. Ceramic glass panel

2. Power cords and plug

3. Brackets for wall or ceiling mounting

4. Remote contro ON/OFF

OPERATING INSTRUCTION FOR IHGB/W15/22S/R MODELS:

1. Ceramic glass panel

2. ON/OFF main power switch

3. Power cords and plug

4. Brackets for wall or ceiling mounting

5. Remote control (IHGB/W15/22SR)

IHGB12SR,

IHGW12SR

IHGB15S/R

IHGW15S/R

IHGB22S/R,

IHGW22S/R

Voltage

230-240V~50Hz

Power

1200 W

1500 W

2200 W

Installation

Wall, Ceiling, flush mounted

Wall, Ceiling, flush

mounted

Wall mounting only

Wall Mounting Height

1,8 – 2,5 m 1,8 – 2,5 m 1,8 – 2,5 m

Ceiling Mounting Height

2 – 3 m 2 – 3 m

Electric Protection Class

Water Splash Proof Rate

IP65

Length of Cable

1,8 m

Dimensions L*W*H

585 x 170 x 80 mm

without bracket

900 x 170 x 80 mm

without bracket

900 x 170 x 80 mm

without bracket

INSTRUCTION FOR IHGB/W12SR

Power on the unit

Standby mode

Set the time function

Plug in the device, the device

will sound 1 beep, the device is

in standby mode, the heating

status lamp is flashing.

Press the button

“standby” on the

remote control, the

device will sound 1

beep and revert to

Standby mode, the

Stand-by lamp is

flashing.

Press the Timer

control button ”1hr”,

to activate 1-hour

delay-off timer

function. The heating

status lamp will turn

to green.

Press the button “ON” on the

remote control, the device

starts to heat, and the heating

status lamp will turn in red.

Power off the unit:

Unplug the device from

the socket or press the

switch or the circuit

break to power off the

device

The device will be

switched off after 1

hour, and revert to

standby mode.

CAUTION: There is a built in safety feature that will automatically trigger the heater to go into

standby mode after eight hours of continuous operation. When this happens, the stand-by

lamp will be flashing.

Heating status lamp

INSTRUCTION FOR ALL OTHER DIMMABLE MODELS

1500/2200:

Power on the unit

Standby mode

Set the time function

Plug in the device, and

then press the switch to

the position I. Point the

remote control directly to

the receiver, press the

button “ON” on the

remote control, the

device will sound 1 beep

and starts to heat in high

power mode (100% the

rated power).

Press the button

“standby” on the

remote control, the

device will sound 1

beep and revert to

Standby mode, the

Stand-by lamp is

flashing.

Press either, or both

of the Timer control

buttons (picture 11),

to activate the delay-

off timer function. (1,

2 or 3-hour options).

1 Hour Timer:

Point the remote

control directly to the

receiver and press the

button of “1hr”. The

1st timer status lamp

will turn to green, the

device will be

switched off after 1

hour, and revert to

standby mode.

All three heating status

lamps will turn in red. The

unit is in heating mode

now.

Power off the unit:

Press the switch to

the position O

2 Hour Timer:

Point the remote

control directly to the

receiver and press the

button of “2hr”, the

2nd lamp of timer will

turn to green color,

the device will switch

off after 2 hours, and

the device will be in

standby mode, and

revert to Standby.

3 Hour Timer:

Point the remote

control directly to the

receiver and press the

button of “1hr” and

“2hr”, both timer

status lamps will turn

to green color, the

device will switch off

after 3 hours, and

revert to Standby

mode.

GB GB

On/off

Switch

Heat Function Display

Timer Function Display

Stand-b y

INSTALLATION DETAILS:

•The ideal mounting position is directly above the area to

be heated with a longitudinal orientation and facing

vertically downwards.

WARNING:

The heater must never be installed in the upwards or

inwards facing position, the heating surface must always be

positioned to direct the heat in a downwards or outwards

direction.

•Find below the minimum clearances when mounting the

heater parallel with a ceiling. (Unit in mm)

•Find below the minimum clearances when mounting the

heater at an angle to the ceiling. (Unit in mm)

•Find below the right wall mounting position. (Unit in mm)

WARNING:

Mounting of the infrared heater and its connection to

the electric mains should be carried out only by

qualified specialists according to the Electrical

Installation Regulations and Power System Safety

Standards.

INSTALLATION PROCESS:

1. Open the factory package and carefully take the heater

out.

2. Take out the packing paper sheet from the end of heater.

3. Take out one pair of mounting Brackets. These adjustable

brackets allow direct ceiling or wall mount, and come with

preset angle options of parallel, 15°, 30°, 45° and height

165mm.

4. The correct installation process, as per the diagram

above, select the heater location on the ceiling by locating

the stud or structural beams to ensure secure fastening of

the heater, whilst observing the minimum clearances from

the floor and other objections.

5. Install two brackets on the ceiling or wall with the

following minimum recommended bracket distance “B”.

6. Set the adjustable angle mounting brackets to desired

angle and fasten brackets by spanner.

165m m

Inclined ceiling mount

Horizontal ceiling mount

Angled horizontal ceiling mount

Fans, lights and

sprinkler fittings

MUST NOT

be below heater

Same on both

ends

1000 mm minimum to surface

(ie table tops, etc)

2100 min. from floor

3000 mm max. from floor

(recommended)

Correct Installation

WALL

CEILING CEILING CEILING

Incorrect Installation

Fans, lights and

sprinkler fittings

MUST NOT

be below heater

Same on both

ends

1000 mm minimum to surface

(ie table tops, etc)

2100 min. from floor

3000 mm max. from floor

(recommended)

Fans, lights and

sprinkler fittings

MUST NOT

be below heater

1000 mm minimum to surface

(ie table tops, etc)

2100 min. from floor

3000 mm max. from floor

(recommended)

Same on both

ends

Correct Installation

WALL

CEILING

IHGB/W15SR, IHGB/W22SR:

CORRECT DISPOSAL OF THIS PRODUCT:

This marking indicates that this product should not be

disposed with other household

wastes throughout the EU. To prevent possible harm to

the environment or human

health from uncontrolled waste disposal, recycle it

responsibly to promote the sustainable

reuse of material resources. To return your used device,

please use the return and collection

systems or contact the retailer where the product was

purchased. They can take this product

for environmental safe recycling.

TROUBLESHOOTING

•Possible malfunctions are given in Table below.

SYMPTOM

CAUSE

Will not heat / No operation indicator

Check that power is connected and switched on.

Heater smells when first used.

This is caused by oil or dust left over from the manufacturing process and will

stop after a short time.

Faint smell for short periods after turning on

the heater.

This is normal and should stop after a short time.

Heater smells when turned on after periods

of no use.

Build-up of debris and dust on the heater, Switch the heater off and allow it

to cool down and then clean.

Clinking noises when heater is turned on and

after being turned off.

This is expansion and contraction noises of the heaters metal components

and is normal.

Poor heating performance.

Exposure to extreme ambient conditions such as high winds / excessively

cold temperatures can lower the heating performance of an outdoor

installation.

Unit is not installed in correct position, possibly too high or heater is too

small for recommended area.

There is a burning smell and or strange

sounds (other than normal expansion and

contraction noises) coming from the unit.

Turn off the heater, and contact the authorized service or seller.

When associated circuit breaker (safety,

ground) is thrown or a fuse is blown.

Turn off the heater and contact the authorized service or seller.

Poor heating performance.

Incorrectly sized installation. Contact the authorized service or seller.

Faulty heater element turns off the heater. Contact the authorized service or

seller.

Will not heat / No operation indicator.

Check that power is connected and switched on, if still faulty, turn off the

heater. Contact the authorized service or seller.

IN-L

IN-N

OUT-L

Heating Element

Switch

1500W

2200W

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Frico Infraglas in the language / languages: English as an attachment in your email.

The manual is 0.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Frico Infraglas

Frico Infraglas User Manual - German - 8 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Frico Infraglas Manual

Product: