787200

Frico Infraflex Manual

8
Zoom out
Zoom in
Previous page
1/10
Next page
Infraflex
8
EN
Maintenance
The power supply to the unit must be
disconnected during all service, repair and
maintenance work. Wait until the unit is cold.
The unit has no moving parts so the
maintenance requirement is small, but it must
be kept clean and free from dust and dirt. If
the reector is not clean the thermal radiation
from the unit will decrease and the heater will
become hotter. A large amount of dirt can
cause overheating.
The surface of the reector is sensitive and
must be cleaned with care. If the reector
is dirty it must be cleaned or replaced by a
specialist.
To clean the casing, wipe it with a soft, dry
cloth. If it is very dirty, use a slightly damp
cloth and, if necessary, a mild detergent. Wipe
afterwards with a dry cloth to remove moisture.
Residual current circuit breaker
When the installation is protected by means of
a residual current circuit breaker, which trips
when the appliance is connected, this may be
due to moisture in the heating element. When
an appliance containing a heater element has
not been used for a long period or stored in
a damp environment, moisture can enter the
element.
This should not be seen as a fault, but is
simply rectied by connecting the appliance to
the main supply via a socket without a safety
cut-out so that the moisture can be eliminated
from the element. The drying time can vary
from a few hours to a few days. As a preventive
measure, the unit should occasionally be run
for a short time when it is not being used for
extended periods of time.
Packaging
Packaging materials are chosen with
consideration to the environment and are
therefore recyclable.
Handling of product at end of working
life
This product may contain substances necessary
for the functionality of the product but
Replacing the lamp and silicon sealing
The heat lamp is of the highest quality and
unless it is subjected to mechanical strains in
the form of vibrations and impact it will last for
a long time. The service life is dependent on
the ambient temperature and how the heater
is installed. When the heater is installed freely
and outdoors the temperature will be low and
the life of the lamp can be expected to be in the
region of 5000 hours.
When replacing the lamp, the silicone sealing
connected to the lamp must also be replaced,
it should be replaced beforehand if there are
signs of aging.
The lamp must be replaced by an installer or
other skilled person.
1. Disconnect the power supply.
2. Wait until the unit is cold.
3. Remove the screws (6x) that holds the two
plastic gables.
4. Remove the plastic gables.
5. Disconnect white cables (no other cables
should be disconnected).
6. Remove the screw for the earth connection
from the reector.
7. Apply some denatured alcohol with a cloth on
the lamp beside the silicone sealing before
removing the lamp.
8. Remove the lamp by pushing it out of one
of the silicone sealings until one end is
free, then it can be pulled out of the second
sealing.
9. Replace the silicone sealings to new ones
(make sure that the sealing is properly
assembled).
10. Apply some denatured alcohol on the new
lamp (at least 10 cm in from each end) before
assembly.
battery life.
• Always use the same type of batteries when
changing them.
• The heater can still be used if the remote
control is missing or not working.
• The remote control may not function should
there be a loss of signal between the remote
control and the heater.
Start-up
When the unit is used for the rst time or after
a long period of non-use, smoke or an odour
may result from dust or dirt which has collected
on the element. This is completely normal and
disappears after a short time.
11. Assemble the new lamp and make sure that
the silicone sealing is tight around the lamp
ends.
12. Reassemble the rest of the unit again
and make sure that no cables are pinched
between gables and inner gable.
… 8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frico Infraflex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frico Infraflex in the language / languages: English as an attachment in your email.

The manual is 2.22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Frico Infraflex

Frico Infraflex User Manual - German - 10 pages

Frico Infraflex User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info