787187
5
Zoom out
Zoom in
Previous page
1/6
Next page
ELIR
7
GB
- Avoid improper use of extension cords.
- Ensure that the heater is aiming its
warmth into the target area. After you have
loosened the screws locking the heater to
the bracket adjust the angle as shown on
page 3.
- If the appliance is not used for a long
period, disconnect it from the power
supply.
Maintenance
When the unit is used for the first time or
after a long period of disuse, smoke or odour
may result from dust or dirt that has collected
on the element. This is completely normal
and disappears after a short time.
During maintenance the heater must be
disconnected from the power supply.
The heater contains no moving parts
and therefore very little maintenance is
required other than to ensure that there is no
excessive build-up of dust/dirt on the reflector
or lamp as this can cause overheating and
premature lamp failure.
To clean the appliance, wipe off with a damp
cloth.
Replacement of lamp
A qualified person shall replace the lamp and
the gaskets.
The lamp is robust and if knocks and shock
vibrations are avoided it will run for a long
time. The expected lifetime of the lamp is
depending on the ambient temperature and
where the heater is installed. When it is
mounted airy the lamp will live longer.
When the lamp is to be replaced the red
silicon gaskets also must be changed. The
gaskets must also be replaced before if there
are signs of aging.
Residual current circuit breaker (E)
When the installation is protected by means
of a residual current circuit breaker, which
trips when the appliance is connected,
this may be due to moisture in the heating
element. When an appliance containing a
heater element has not been used for a long
period or stored in a damp environment,
moisture can enter the element.
This should not be seen as a fault, but is
simply rectified by connecting the appliance
to the mains supply via a socket without a
safety cut-out, so that the moisture can be
eliminated from the element. The drying
time can vary from a few hours to a few days.
As a preventive measure, the unit should
occasionally be run for a short time when it is
not being used for extended periods of time.
Safety
For all installations of electrically heated
products should a residual current circuit
breaker 300 mA for fire protection be used.
During operation the surfaces of the unit
are hot!
The unit must not be fully or partially
covered with inflammable materials, as
overheating can result in a fire risk!
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
The heater is equipped with a protective
grille to prevent contact or to prevent
large objects from touching the hot lamp.
The unit must not be used without this
protective grille.
Ensure that there are no inflammable
materials gathered on or close to the
heater.
The free space to the inflammable material
in the direction of radiation must be at
least 1 meter.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Frico ELIR12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Frico ELIR12 in the language / languages: English as an attachment in your email.

The manual is 0.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info