Manual Franke FIM 1100 W XS (page 6 of 60) (English, German, Dutch, French, Italian, Spanish)

510247

Zoom out

Zoom in

1/60

2) Place the brackets item 7.2 on the wall about 1 or 2 mm from the ceiling or from the upper limit, aligning

its centre on the vertical line. Mark the two eyelet holes of the bracket onto the wall. Drill the holes

for the ﬁxing bracket using an 8 mm masonry bit. Fix the chimney bracket item 7.2 using the screws

item 12a and rawl plugs item 11 supplied.

3) Mark a point on the vertical line at a distance from the cooking appliances of:

d = 1070 mm (Measurement without splashback).

d = height of the splashback (400 mm) + 670 mm (Measurement with splashback item B).

The distance H is the minimum height in mm from the cooking appliances to the bottom edge item L2 of

the front panel of the hood. Draw a horizontal line through the vertical as illustrated in Fig. 1.

Splashback (optional): When a splashback is to be ﬁtted, the distance between the hood and the cook-

ing appliances will be determined by the height of the splashback item B and whether or not there

is a raised back on the worktop. The splashback is to be installed before installing the canopy. If

the splashback is to be ﬁxed to the wall using both the top and bottom ﬁxing holes, Care must be

taken to ensure that the splashback is ﬁtted at the correct height before ﬁxing the base units or at

least the worktop covering them. As this is a complex operation, it should only be undertaken by

the technician installing the kitchen units or by a competent person who knows the ﬁnal dimensions

of the units.

Mark the hole centres for the canopy ﬁxing brackets item 7.1 at item B mm as illustrated in Fig. 1.

Drill the 4 holes for the ﬁxing brackets using an 8 mm masonry bit. Fix the wall brackets item 7.1 using

the screws item 12b and rawl plugs item 11 supplied.

1070

260

7.1

12a

4) Hook the canopy item 1 onto the wall brackets

item 4 as illustrated in Fig. 2. To ensure the cooker

hood is aligned correctly adjust the screws on the top

of the canopy as illustrated

. When the hood is

aligned correctly mark the hole centre on the wall for

the security ﬁxing screw

, which is located in the right

hand bracket on the top of the canopy. Unhook the

canopy from the wall and drill the hole for the security

ﬁxing screw. Hook the canopy onto the wall and ﬁx the

headed screw item 12.a and rawl plug item 11 to

secure the canopy to the wall.

5) Ducting:

The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker

hood is ducted to the outside, charcoal ﬁlters are not required.The ducting used must be 150 mm (6

INS), rigid circular pipe and must be manufactured from ﬁre retardant material, produced to BS.476

or DIN 4102-B1. Wherever possible use rigid circular pipe which has a smooth interior, rather than

the expanding concertina type ducting.

Maximum length of ducting run:

- 4 metres with 1 x 90° bend.

- 3 metres with 2 x 90° bends.

- 2 metres with 3 x 90° bends.

The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components

and ducting kits are optional accessories and have to be ordered, they are not automatically sup-

Fig. 2

plied with the chimney hood.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Franke FIM 1100 W XS in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 7,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Franke FIM 1100 W XS Manual

Product: