803528
317
Zoom out
Zoom in
Previous page
1/412
Next page
69
EN
Theaxlenutsmustbecorrectlyfastened
after each chain adjustment process.
Work may only be performed on the
chain once the electrical system has
been switched o󰀨 and the battery has
been removed. If the chain of your
FLYER e-bike has fallen o󰀨 the chain
ring or sprocket, it is essential to switch
o󰀨theelectricalsystemandremovethe
battery before placing the chain back on
the gear wheels.
Chain care
The drive chain must be cleaned and lubricated
regularly in order to ensure that it functions well
(see section “Inspection plan”).
Dirtcansimplybewashedo󰀨.Youcanalsoclean
the chain by wiping it with an oil-soaked cloth.
Once it is clean, it must be lubricated at the joints
with a suitable lubricant. After leaving for a short
while,wipeo󰀨theexcesslubricant.
Belt drive
The Gates Carbon Drive belt is very durable and
long-lasting. However, you must take extreme
care before and during assembly to ensure that
no damage is caused to the carbon bres that
makeupthe strengthof thedrivebelt. Extreme
bending and twisting causes tears that can lead to
faults in the belt if subjected to high stress.
1
10-15 mm
2
3
Follow the instructions for handling the Gates
Carbon Drive System belt and observe the provi-
sions in the user manual.
Drive belt and chain tighten if the bike has
sliding dropouts
Adjusting the tension and alignment of
thebeltrequiresagreatdealofexperi-
ence. Improper handling can cause acci-
dents and severe falls. Always let your
FLYER specialist retailer perform this
activity.
If the tension of the drive belt is too low,
this can cause it to slip on the toothed
pulley. This may result in accidents or
severe falls.
The carbon bres inside the drive belt
may also be damaged. If the drive belt
slips through, take it to a specialist to be
checked over.
If the tension of the drive belt is too high,
bearings and seals in the wheel hub can
become damaged. The wear and friction
losses on the entire drive are therefore
also higher.
Thecarbonbresinsidethedrivebeltmayalso
be damaged. If the drive belt slips through, take it
to a specialist to be checked.
If the tension of the drive belt is too high, bearings
and seals in the wheel hub can become dam-
aged. The wear and friction losses on the entire
drive are therefore also higher.
Tightening the toothed belt
Loosen the screws A1 on both sides of the dro-
pout. You only need to loosen the
screws until the dropout can move freely.
A1
Tighten the chain/toothed belt using the adjusting
screw A2. You have reached the correct chain
tension when the chain is still able to move up
and down slightly in the centre (10-15 mm). Use
a belt tension measuring device to check that the
belt tension is correct. Consult the belt manufac-
317


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Flyer Crossocver - Fit 2022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Flyer Crossocver - Fit 2022 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 34.98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info