624062

Fluke networks TS 100 Cable Fault Finder Manual

19
Zoom out
Zoom in
Previous page
1/20
Next page
15
Specifications
Specifications
Power 4 AA alkaline batteries, provide 50 hours of operation
Reverse Battery
Protection
No damage to the tester will occur if the batteries are installed backwards.
Input Protection 250 V rms ac, continuous or intermittent
Moisture If the tester is exposed to water, some may get inside, but it will suffer NO DAMAGE. See the
information on moisture under “Maintenance”.
Impedance Range
35 Ω to 330 Ω with auto-compensation within this range. Cables with an impedance outside
this range will not be properly tested and may produce erratic or incorrect readings.
Maximum Length
2500 feet (770 meters) on certain cable types, 2000 feet (610 meters) on most cable types,
and 500 feet (152 meters) on very lossy cables. The tester will display –Err if the cable is too
long to be correctly measured.
Representative
Maximum Cable
Length
2500 feet (770 meters): CAT-5 Twisted Pair
2000 feet (610 meters): 12/2 ac Wire
1000 feet (300 meters): RG-6/U TV Coax
500 feet (152 meters): RG-174/U Coax
Minimum Length No minimum length. Minimum non-zero reading is 2 feet (1 meter)
Length Accuracy ±2 feet (±609 mm) for cables less than 10 feet (3 mm)
±5 feet (±2 meters) for cables longer than 10 feet (3 meters) and shorter than 200 feet (60
meters)
±3 % and ±5 feet (±2 meters) for cables longer than 200 feet (60 meters)
High Voltage
Detection
An ac voltage of more than
5 V rms will trigger the High Voltage Warning.
Measurement Rate Maximum of 4 complete measurements per second, decreasing to 2 seconds per
measurement based on cable size and uniformity.
VOP Adjustable from -20- to -99-, retained during power off. Default to -66- when batteries are
changed
Measurement
Technology
Time Domain Reflectometry (TDR) with 50 Ω drive impedance, 6 V maximum pulse height
Low Battery Indicator flashes when battery voltage falls below 4.1 V
-continued-
… 19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke networks TS 100 Cable Fault Finder at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke networks TS 100 Cable Fault Finder in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info