763940

Fluke 8808A Manual

69
Zoom out
Zoom in
Previous page
1/100
Next page
Operating the Meter Using the Computer Interface
Triggering Output 4
4-9
+/- 1.0E+9 Overload (0L on the display)
Triggering Output
The Meter takes measurements when triggered to do so. There are five trigger types,
which are described in Table 4-3. Triggers fall into two basic categories:
• Internal trigger, which triggers measurements continuously.
• External trigger, which triggers a measurement at the direction of the user.
A measurement can be externally triggered as follows:
• External trigger with rear trigger disabled. This includes trigger types 2 and 3, as
described in Table 4-3.
• External trigger with rear trigger enabled. This includes trigger types 4 and 5, as
described in Table 4-3.
• *TRG command
For use of the *TRG command, see “Common Commands.”
Table 4-3. Trigger Types
Type Trigger Rear Trigger Settling Delay
1 Internal Disabled —
2 External Disabled Off
3 External Disabled On
4 External Enabled Off
5 External Enabled On
External Triggering from the Front Panel
To enable external triggering from the front panel, perform the following procedure:
1. Press Q then J. Ext Trig and a number corresponding to the selected trigger
type (1, 2, 3, 4, or 5) are displayed. See Table 4-3 for trigger types.
2. Press U or V to step through the trigger type list. Highlight the trigger type as
follows, and then press R for two seconds to select it.
3. Select trigger type 2 to disable the settling delay; or select trigger type 3 to enable the
settling delay. See Table 4-3 for typical settling delays.
4. When trigger type 2 or 3 is selected, Ext Trig is displayed confirming that you are not
in the remote mode and an external trigger is enabled. (If you are not in the remote
mode, you will not be able to trigger measurements from the front panel.)
5. Press J to trigger a measurement. (Each time you press J you trigger a
measurement.)
6. To return the Meter to its internal (continuous) trigger state, perform step 3 and select
trigger type 1.
If you enter the remote mode with trigger type 4 or 5 selected, the Meter remains in
its external trigger state; however, because the Meter is in the remote mode, you will
only be able to trigger measurements with rear trigger types 4 and 5. To exit remote
mode, perform steps 1 and 2 and select trigger type 2 or 3 (as applicable).
… 69 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 8808A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 8808A in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 8808A

Fluke 8808A User Manual - German - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info