763940

Fluke 8808A Manual

56
Zoom out
Zoom in
Previous page
1/100
Next page
8808A
Users Manual
3-22
Table 3-6. Second Level Operations (cont.)
Buttons Description
Q and V[1] In COMP mode, stores value on primary display as LO compare point (see
the “Using the Compare Function” section later in this manual)
Q and U[1] In COMP mode, stores value on primary display as HI compare point (see
“Using the Compare Function”)
[1] Hold both buttons for 2 seconds.
Compare Function (COMP)
The Meter has a compare function (COMP) that provides an easy way to determine if a
reading falls within a designated range of values. The compare function can be used with
any function modifier.
Setting the Compare Range
Before selecting the compare function, you need to set the tolerance range against which
the reading that will be compared. This can be done in any of the following three ways:
• Press C to enter the compare function mode. The reading displayed when you
enter the mode can be set to the high or low threshold. To set the reading as the
high limit, press and hold Sand U for 2 seconds. To set the reading as the
low limit, press and hold Sand V for 2 seconds. The Meter beeps to
indicate the limit has been set. If the display is blank or shows 0L (overload), the
limit could not be set and the high and low limits remain as previously set.
• Use the number editor as described in the “Using the Number Editor” section
later in the chapter. (Before entering the number editor, be sure you are in the
appropriate range.) The decimal point and input range are fixed according to the
range in the editor.
• Use the computer interface commands COMPHI and COMPLO to set the high and
low compare points remotely. See the “Compare Commands and Queries”
section in Chapter 4.
Using the Compare Function
To select the compare function, press C. When the compare function is first selected,
the Touch Hold function is also activated and H is displayed. To turn off Touch
Hold, press and hold I for 2 seconds. The secondary display will then update with
each new reading.
When a stable value is detected, the Meter beeps if hold is on and the reading is shown in
the primary display. If the value is within the range you set, PASS is shown in the
secondary display. If the value is not within the set range, HI or L0 is shown as applicable
in the secondary display.
List and Number Editors
The Meter has a list editor and number editor. The list editor allows you to scroll through
and select from a list of options. The number editor allows you to enter or edit a numeric
value.
Editing is performed in the primary display. Normal operation of the Meter is interrupted
when either editor is invoked. If a computer interface command is received by the Meter
during editing, the edit is aborted and the Meter returns to normal operation. The item
being edited is not changed.
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 8808A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 8808A in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 8808A

Fluke 8808A User Manual - German - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info