763940
53
Zoom out
Zoom in
Previous page
1/100
Next page
Operating the Meter from the Front Panel
Selecting a Function Modifier 3
3-19
Table 3-5. dBM Reference Impedances
Impedance Impedance Impedance
8000 Ω 300 Ω 93 Ω
1200 Ω 250 Ω 75 Ω
1000 Ω[1] 150 Ω 50 Ω
900 Ω 135 Ω 16 Ω[2]
800 Ω 125 Ω 8 Ω[2]
600 Ω 124 Ω 4 Ω[2]
500 Ω 110 Ω 2 Ω[2]
[1] Voltage annunciator lit
[2] Audio power readings possible
To access the reference impedance list, press Q then press W. The reference
impedance currently selected is displayed, along with the "db" and "ohm" annunciators.
Press U or V to scroll to the desired value, then press R to select a reference
impedance and return the primary display to the measurement function. Press any
function or modifier button to exit the reference impedance list without selecting a new
value.
Setting the dB reference resistance to 16, 8, 4, or 2 ohms allows you to use the Meter to
calculate audio power. After the reference resistance has been set to 16, 8, 4, or 2 ohms,
press W twice to select the audio power modifier. Power annunciator will be displayed.
The following equation is used to make a power calculation (volts is the measurement
value):
ref
R
Volts
PowerAudio
2
=
Touch Hold Function (HOLD)
The Touch Hold function holds the results of your measurements on the display. Touch
Hold is helpful in difficult or hazardous circumstances when you want to keep your eyes
fixed on the probes and reading the display only when it is safe or convenient to do so.
When a new, stable reading is detected, a beep is emitted and the display is automatically
updated.
To select the Touch Hold function, press I. H is displayed. In Touch Hold, each
time you press I, a new reading is displayed. To exit the Touch Hold function, press
and hold I for 2 seconds.
If you are in the autorange mode when Touch Hold is selected, you will autorange to the
correct range. If you are in the manual range mode when Touch Hold is selected, you will
be in the fixed range you were in when Touch Hold was selected.
The Touch Hold function can be combined with the minimum/maximum modifier to hold
and update only when a new minimum or maximum value is detected. To force the
display to update, with Touch Hold selected press I for less than 2 seconds.
The Meter allows you to choose the minimum response level needed for Touch Hold to
capture and display a measurement. You can choose from the following four response
levels:
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 8808A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 8808A in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 8808A

Fluke 8808A User Manual - German - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info