764273
42
Zoom out
Zoom in
Previous page
1/50
Next page
709/709H/710
Users Manual
36
If the positioner is configured to be reverse acting, the relationship
of mA signal to control valve opening and closing is reversed.
Configuration for forward or reverse action does not change the
mode in which the valve fails.
TV: This variable is the pressure applied to the pneumatic actuator
by the valve positioner. With 4 mA applied in a Direct Acting
positioner, the minimum or 0 psi of pressure is applied and the
valve spring holds the valve into the failure mode position (FO or
FC). With 20 mA applied, the direct acting actuator has maximum
pressure applied to the actuator from the positioner moving it to
the 100 % position and the opposite of the failure position.
Reverse acting actuators respond opposite of direct acting
actuators with 4 to 20 mA signals applied.
QV: This is the position feedback variable (0 % to 100 %). The
position feedback variable should agree closely with the Setpoint
variable (SV). If it does not, the positioner should be calibrated to
better match the position of the valve or repair is required.
To run the manual test:
1. Push the , and to change the valve position and
the mA output.
2. Manually compare the variable to what is expected.
Note
When the Valve Test is set to ON (Figure 13),
changes the mA signals to step with stops at 3.8 mA,
4.2 mA, 19.8 mA, and 20.2 mA to make manual valve
testing easier (see Valve Test).
Speed Test
The Speed Test is a test of the time it takes to open and close the
valve.
To set up the expected time to cycle the valve in seconds from
10 seconds and up:
1. Move the cursor to the digit to change.
2. Rotate the selection knob to change the time value.
3. Push the selection knob to input the change.
Figure 54. Speed Test
To run the test:
1. Push to start the test.
Good test result: the position variable is as expected.
Marginal test result: the position variable value is found to
be close to the test tolerance.
Bad test result: the position variable deviation values vary
greater than the tolerance.
2. Select Save to save the test results and upload later to the
ValveTrack software.
Or, select Discard if you do not want to save the test result.
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fluke 709 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fluke 709 in the language / languages: English as an attachment in your email.

The manual is 5,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fluke 709

Fluke 709 User Manual - German - 50 pages

Fluke 709 User Manual - Dutch - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info