783798
10
Zoom out
Zoom in
Previous page
1/112
Next page
10
GB IE
Personal safety
CAUTION: In this way you avoid ac-
cidents and injuries:
Stay alert, watch what you are
doing and use common sense
when operating a power tool.
Do not use a power tool while
you are tired or under the inu-
ence of drugs, alcohol or medi-
cation. A moment of inattention white
operating power tools may result in seri-
ous personal injury.
Wear personal protective equip-
ment and always wear safety
glasses. Wearing personal protective
equipment such as nonslip safety boots,
cut protection trousers, a hard hat or ear
protection reduces the risk of injuries.
Prevent unintentional starting.
Ensure the switch is in the off-
position before connecting to
power source and/or battery
pack, picking up or carrying the
tool. Carrying power tools with your
nger on the switch or energising pow-
er tools that have the switch on invites
accidents.
Remove any adjusting key or
wrench before turning the pow-
er tool on. A wrench or a key left
attached to a rotating part of the power
tool may result in personal injury.
Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the power
tool in unexpected situations.
Keep your hair, clothing and
gloves away from moving parts.
Jewellery or long hair can be caught in
moving parts.
Warning! During operation, this elec-
tric tool generates an electromagnetic
frigerators. There is an increased risk
of electric shock if your body is earthed
or grounded.
Do not expose power tools to
rain or wet conditions. Water en-
tering a power tool will increase the risk
of electric shock.
If the supply cord of this power tool is
damaged, it must be replaced by a spe-
cially prepared cord available through
the service organization.
If it is necessary to replace the connection
cable, we recommend that this be perfor-
med by the manufacturer or an authorised
representative (e.g. authorised workshop,
customer service, etc.).
Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk of
electric shock.
When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
If operating a power tool in a
damp location is unavoidable,
use a residual current device
(RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
Connect the appliance to a power sock-
et with a residual current circuit breaker
of rated residual current no more than
30 mA.
Use only approved power cable of
type H05RN-F, which are no more than
75 m in length and intended for use
outdoors. The conductor cross section
of the cord must be at least 2.5 mm
2
.
Always fully unroll a cable drum before
use. Check the power cord for damage.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FKS 2200 E3 - IAN 275658 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FKS 2200 E3 - IAN 275658 in the language / languages: English, German, Dutch, Danish as an attachment in your email.

The manual is 1.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info