576523
59
Zoom out
Zoom in
Previous page
1/76
Next page
59
GB

Check the oil ll level and regularly top
up with oil (
C
20). The oil tank holds
270 ml oil.
Use Parkside bio-oil; this product con-
tains additives that reduce wear and
tear and does not damage the pump
system. bio-oil is available from our
Service-Center.
If you have no Grizzly bio-oil available,
use chain lubrication oil with low adhe-
sive additive content.
C
1. Unscrew the oil ll cap (2) and ll
up with chain oil.
2. Wipe off any spilled oil and
close the cap again.
Operating the chainsaw
Switch on the chainsaw only when
chain bar, saw chain and sprocket
chain wheel covering are correctly
assembled. Ensure the voltage of the
mains connection agrees with the
label on the device. Make sure you
have a secure stance
: The saw is a high-powered
device, where a 13 A fuse gener-
ally sufces, provided that further
current consumers with high service
are not connected. However, if
the premises installations are not
implemented optimally and “quick-
acting” protection fuses are built-in
(e.g. B 16), the protection fuse
will be activated due to the current
peaks during switch-on. You should
install time-delay fuses with the des-
ignation “L, which can be bought
in every hardware store. Fuses with
the designation “G” are provided
with even longer time delay, how-
ever they are not usually employed
in households.
Caution! Saw can oil up, see notes
on Operation startup.
Switching on
D
1. Check before the start, whether
sufcient chain oil is in the tank
and, if necessary, rell with chain
oil (see Chapter Operation Start).
2. Form a loop from the end of the
extension cable and hang this
into the tension relief (17) on the
rear grip (1).
3. Connect the device to the mains
voltage.
4. Release the chain brake, where
you shift the brake arm (3) back
against the front grip (8).
5. Hold the electric chainsaw rmly
with both hands, with the right
hand on the rear grip (1) and
the left hand on the front handle
(8). Thumb and nger must close
securely over the handles.
6. For switching on, activate the
switch-on block (11) with the right
thumb and then press the On/Off
switch (10), the electric power
saw runs with highest speed.
Release the switch-on block
again.
7. The power saw switches off when
you release the On/Off switch
(10) again. Switching for continu-
ous running is not possible.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FKS 2200 B1 - IAN 72314 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FKS 2200 B1 - IAN 72314 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 4,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info