783807
11
Zoom out
Zoom in
Previous page
1/82
Next page
11
GB IE
(18). Release the safety release
catch (17).
The tines (
A
11) will begin to
rotate and dig themselves into
the earth.
6. To switch off, release the dead-
man lever (18).
Warning! The tines will con-
tinue to turn for a few sec-
onds after the tool has been
switched off. Do not touch
the rotating tines – injury
hazard!
Operating instructions
Alwayskeeparmgripon
the tool with booth hands
and watch your feet.
The tines (11) may cause an
accident. Be careful while
moving backwards – danger
of tripping!
Do not touch the gearbox, as
it may become hot during op-
eration – danger of burns!
Switch the tool off after working
with it and for transport; disconnect
from the mains and wait for the
tines to stop moving.
To avoid damage to the
tool:
Never lift or drag the tool with
the motor running.
Lift the tool while moving it over
hard surfaces such as tiles or
steps.
Walk the tool through the soil
at normal pace and in a line as
straight as possible.
Always work away from the
mains socket. Make sure that
the cable is kept well away from
the working area. Hanging the
cable into the belt clip included
in the package will help.
Overload protection: The motor
will cut out immediately if overload-
ed. The tool cannot be used until it
has completely cooled down again.
Cleaning/Maintenance
Always return the tool to the service
centre for work not described in the
manual. Only use original parts.
Switch the tool off, unplug it from
the mains, and wait for the tines
(11) to stop moving before carrying
out any maintenance or cleaning
work on the tool.
Perform regular maintenance and cleaning
on the tool. This will ensure long, reliable
service.
General cleaning and
maintenance work
Do not spray the tool down
with water (especially not
under pressure), and do not
clean it under running water.
Wear protective gloves when carry-
ing out maintenance and cleaning
work on the tool to avoid injury
from cuts.
Always clean the tool thoroughly after
each use. Always keep the tool clean. Do
not use cleaning uids or solvents.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FGH 710 A1 - IAN 102836 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FGH 710 A1 - IAN 102836 in the language / languages: English, German, Dutch, French, Swedish, Finnish as an attachment in your email.

The manual is 2.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info