Manual Florabest FBS 43 A1 (page 61 of 70) (German, Dutch, French)

539572

Zoom out

Zoom in

1/70

- 63 -

tighten the handle screw as shown in Figure 4c. To

dismantle, simply slacken the handle screw and

actuate the locking lever.

6.1.3 Fitting the blade guard hood

Important: The cutting blade guard hood (15)

must be ﬁ tted when you want to work with the

cutting blade.

The guard hood for the cutting blade must be ins-

talled as shown in Figures 5a – 5b.

6.1.4 Fitting/Replacing the cutting blade

The procedure for ﬁ tting the cutting blade

(18a/18b) is shown in Figures 6a-6g. To dismant-

le, proceed in reverse order.

•

Fit the carrier plate (22) onto the spline shaft

as shown in Figure 6b.

•

Secure the cutting blade (18a/18b)) on the

carrier plate (Fig. 6c).

•

Place the pressure plate (23) over the thread

of the spline shaft (Fig. 6d).

•

Plug on the cover of the pressure plate (24)

(Fig. 6e).

•

Look for the hole in the carrier plate, line up

with the notch underneath, lock with the sup-

plied hex wrench (29), and then tighten the

nut (25) with the spark plug wrench (27) (Fig.

6f/6g). Important: Left-hand thread

•

The cutting blades (18a/18b) are delivered

with plastic protective caps fitted to them.

Remove these caps before use and refit them

after use.

6.1.5 Fitting the cutting line guard hood

on the cutting blade guard hood

Important: The cutting line guard hood (14) must

be ﬁ tted in addition when you want to work with

the cutting line.

The guard hood for the cutting line must be ins-

talled as shown in Figures 7a – 7b. Make sure

that the cutting line guard hood engages correctly.

A blade (Fig. 7a/ Item F) on the underside of the

guard hood automatically cuts the cutting line to

the optimum length. It is covered by a guard (Fig.

7a/Item G).

Remove the guard before you start working and

replace it when you have ﬁ nished working.

6.1.6 Fitting/Replacing the line spool

The procedure for ﬁ tting the line spool (13) is

shown in Figure 7c. To dismantle, proceed in re-

verse order. The line spool is already ﬁ tted when

the equipment is delivered.

Look for the hole in the carrier plate (22), line up

with the notch beneath it, lock with the supplied

hex wrench (29), and screw the line spool onto

the thread.

Important: Left-hand thread

6.2 Setting the cutting height

•

Fit the carrying strap (17) as shown in Figures

8a-8c.

•

Hook the equipment to the carrying belt (Fig.

8d).

•

Adjust to the perfect working and cutting po-

sition using the various strap adjusters on the

carrying strap (Fig. 8e).

•

To confirm the optimum length of the carrying

strap, make a few swinging movements with

the engine off (Fig. 9a).

The carrying strap is ﬁ tted with a quick-release

mechanism. Pull the red strap section (Fig. 8f) if

you need to remove the strap quickly.

Important: Always use the strap when working

with the equipment. Attach the strap as soon as

you have started the engine and it is running in

idle mode. Switch off the engine before you take

off the carrying strap.

6.3 Fuel and oil

Recommended fuels

Use only a mixture of unleaded petrol and special

2-stroke engine oil.

Mix the fuel mixture as indicated in the fuel mixing

table.

Important: Do not use a fuel mixture which has

been stored for longer than 90 days.

Important: Never use 2-stroke oil with a recom-

mended mixing ratio of 100:1. The manufacturer’s

warranty will be voided in case of engine dama-

ge due to inadequate lubrication.

Important: Only use containers designed and

approved for the purpose to transport and store

Anleitung_3401991_LB2.indb 63Anleitung_3401991_LB2.indb 63 24.02.12 14:0924.02.12 14:09

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBS 43 A1 in the language / languages: German, Dutch, French as an attachment in your email.

The manual is 3,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Florabest FBS 43 A1 Manual

Product: