630794

Florabest FBM 575 B1 - IAN 93561 Manual

15
Zoom out
Zoom in
Previous page
1/52
Next page
15
GB IE
Operation
Observe the noise protection and
local regulations.
Starting and Stopping the
Engine
Warning! Petrol is amma-
ble. Start the engine at least
3 m away from the lling lo-
cation. There is a risk of re.
Start the equipment on a sturdy,
level base, if possible not in long
grass. Ensure that the cutting tool
is touching neither objects nor the
ground.
Check the petrol and oil levels regu-
larly (see “initial operation”) and
rell in time.
Start the Engine:
1. Pull the safety catch (3) towards
the handle bar and hold it.
2. Pull the starter cord (25) and the
engine starts.
3. When the engine starts, allow
the starter handle (25) to slowly
slide back into the starter cable
guide (26).
Stopping the Engine:
4. Release the safety catch (3), the
engine stops and the blade is
slowed.
Mowing
1. Start the engine (see “Starting
and Stopping the Engine”).
2. Wheel drive on: pull the drive
catch (1) towards the handle bar
(2). The mower moves forwards.
3. Wheel drive off: release the
drive catch (1). The equipment
stops.
Working Instructions
General Working Instructions
• As far as possible, mow the lawn
when it is dry in order to protect the
turf.
• Set the cutting height such that the
equipment is not overloaded.
• Run the equipment at walking speed
in lines that are as straight as possible.
For uninterrupted mowing, the lines
should always overlap by a few centi-
metres.
• Do not move backwards.
• On slopes, always work across the
slope.
• If the blade comes into contact with
a foreign body, switch off the engine
immediately. Wait until the blade is
stationary and check the equipment
for damage. Restart work only if the
equipment is undamaged.
• Switch off the equipment during longer
breaks and for transportation and wait
until the blade is stationary.
• Clean the equipment after each use, as
described in the “cleaning and mainte-
nance“ chapter.
Setting the Cutting Height
The equipment has 7 positions for setting
the cutting height (30-95 mm):
1. Pull the lever (20) outwards and
push it to the desired position
(38).
2. Push the lever (20) back in.
… 15 …


Need help? Post your question in this forum.

Forumrules
1

Forum

florabest-fbm-575-b1---ian-93561

Reset search

  • l
    How can I reattach the drive wheel on Florabest 575 Submitted on 22-6-2022 at 13:33

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FBM 575 B1 - IAN 93561 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBM 575 B1 - IAN 93561 in the language / languages: English, German as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info