679100
14
Zoom out
Zoom in
Previous page
1/53
Next page
FBKS 52 A1
10 
GB
IE
NI
Checking and adjusting the chain lubrication
CAUTION!
Never work without chain lubrication!
If the saw chain runs dry, the cutting equipment may become irre-
parably damaged in a short time.
Always check chain lubrication before starting work.
NOTE
Use only saw chain oil. Preferably biodegradable. Do not use waste
oil, motor oil, etc.
While working, check whether the chain lubrication is working
correctly.
With the chainsaw running at a medium speed, hold it over a sawn off
tree stump or a suitable ground sheet.
If the lubrication is adequate, a light film of oil will form on the tree
stump or the ground sheet (see fold-out page fig. E).
If required, the chain lubrication can be increased or decreased using
the oil adjusting screw
.
To do this, use the supplied flat-head screwdriver
.
Press and then turn the oil adjusting screw
clockwise to decrease the
chain lubrication.
Press and then turn the oil adjusting screw
anticlockwise to increase
the chain lubrication.
Checking the chain brake
WARNING!
You must check the chain brake before every use.
The chain brake stops the saw chain in the event of a kickback.
Make sure that the front hand guard
is free of dirt and moves freely.
While the engine is running, push the front hand guard
forwards
until it clicks into place.
Pull the throttle control
briefly to the stop (full throttle).
The saw chain
should not move.
WARNING!
High engine revs over a long period with the engine brake engaged
will damage the engine and the chain drive.
If the saw chain
moves anyway, contact Customer Service.
Basic working procedures when
felling trees
RISK OF INJURY!
Sawing and felling work as well as all associated tasks may only be
carried out by properly trained operators.
NOTE
Note your country's laws regarding felling work and contact the
appropriate authority for more information.
Make sure that no one can be injured by falling branches and trees.
Only the required personnel should be in the working area.
Keep the area around the trunk free and tidy to ensure secure footing
for the operators.
Keep all escape routes free and tidy to ensure that the working area
can be evacuated quickly.
Do not carry out any felling work in strong wind, poor weather or bad
visibility.
Keep a distance of at least 2½ tree lengths from next working area.
Use and handling
Never start the appliance before the guide rail
, saw chain and
sprocket cover
have been fitted correctly.
Do not cut any wood that is lying on the ground and do not attempt
to saw roots that are protruding from the soil. Never immerse the saw
chain
in the soil, as this could blunt the saw chain .
If the appliance accidentally comes into contact with a solid object, turn
off the engine immediately and inspect the appliance for damage.
Service the appliance carefully. Check for misalignment or binding
of moving parts, breakage of parts and any other damage that may
impair the tool’s operation. If damaged, have the appliance repaired
before use. Many accidents are caused by poorly maintained tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
Have the appliance checked by qualified specialists. Use only the
replacement parts recommended by the manufacturer.
Preparing the kerf (see fold-out page fig. F)
NOTE
The kerf determines the direction that the tree will fall in.
Place the kerf at right angles to the fall direction.
Saw as close the ground as possible.
Support the chainsaw using the bumper spike
.
Start with the first kerf cut A.
The depth of the kerf should be about 1/4 of the diameter of the tree
and at an angle of 45°–60°.
Make the felling cut B around 2–3 centimetres higher than the hori-
zontal kerf cut A. Ensure that the felling cut B is perfectly horizontal.
14


Need help? Post your question in this forum.

Forumrules
1

Forum

florabest-fbks-52-a1---ian-302393

Reset search

  • lOOK FOR ON / OFF SWITCHES FOR ELECTRIC SAW FOR Florabest FKS 2200 D2 Submitted on 25-8-2020 at 20:21

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Florabest FBKS 52 A1 - IAN 302393 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Florabest FBKS 52 A1 - IAN 302393 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 3,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info