383715

Flex ske 2902 vv Manual

10
Zoom out
Zoom in
Previous page
1/102
Next page
10
Periodically clean the blade clamp with dry compressed air. DO NOT lubricate the blade clamp.
Lubricant can attract contamination.
Wear ANSI Z87.1 safety glasses while using compressed air.
DUAL BLADE MOTION
Model SKE 2902 VV has dual blade motion: you have a choice of straight reciprocating motion, as shown
in Fig. 8, or orbital motion as shown in Fig. 9. Straight reciprocating motion should be used for all metal
cutting operations, and for wood cutting applications where finish is more important than speed. Orbital
motion is used for fast cutting of wood.
To set saw for straight reciprocating motion: rotate knob (A) Fig. 8, clockwise so that the bar is vertical
(opposing arrow symbol up), as shown in Fig. 8.
To set saw for orbital motion: rotate knob (A) Fig. 9, counterclockwise so that the bar is horizontal (oval
arrow symbol up), as shown in Fig. 9.
PIVOTING GUIDE SHOE
The pivoting guide shoe (A) Fig. 10 serves as a rest while making a cut and it can be adjusted to
accommodate many types of cutting applications.
DISCONNECT TOOL FROM POWER SOURCE.
DO NOT OPERATE THE SKE 2902 VV WITH THE GUIDE SHOE
REMOVED.
The SKE 2902 VV is supplied with a keyless Quik-Change™ pivoting guide shoe. To adjust, rotate lever
(A) Fig. 11 releasing the pivoting guide shoe (B). Adjust to desired position and close lever (A) Fig. 12.
The keyless Quik-Change™ pivoting guide shoe is designed with a raised lip (C) Fig. 11 at the end that
prevents the guide shoe from locking in position if it is extended out too far. After adjusting, make sure the
locking lever is completely closed in the locked position (A) Fig. 12.
NOTE: DO NOT force the locking lever closed. Adjust shoe enough to allow the lever to lock in
position without force.
USING THE SAW
BEFORE YOU START TO WORK
Select the blade best suited for the material to be cut. For greatest economy, use the shortest blade
suitable for the thickness of the material to be cut.
Be sure the material to be cut is rigid. Small work pieces should be securely clamped in a bench vise or
with clamps to the work table. As the work progresses in scroll or curved cut-out pieces, the material may
be readjusted to accommodate the movement of the saw. If the work is large enough, it may be held only
by hand across saw horses. The saw cuts freely with only slight feed pressure. Forcing the saw will not
make it cut faster.
SAWING WOOD
The SKE 2902 VV is used much the same as a hand saw in that it is moved toward the operator during
the cutting operation. However, since the blade cuts on the up-stroke instead of the down-stroke as in the
case of the hand saw, the good or finish side of the work should face down during the cutting operation.
PLUNGE CUTS
The SKE 2902 VV can be used for plunge cutting wood, plywood, wallboard, and plasticmaterials.
DO NOT attempt to plunge cut metal.
WARNING
WARNING
WARNING
SKD.book Seite 10 Dienstag, 29. August 2006 8:42 20
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Flex ske 2902 vv at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Flex ske 2902 vv in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info