383715

Flex ske 2902 vv Manual

9
Zoom out
Zoom in
Previous page
1/102
Next page
9
OPERATING INSTRUCTIONS
FOREWORD
The FLEX SKE 2902 VV is designed for cutting wood up to 30.5 cm thick, metal up to 19 mm thick and
various other materials, such as plastics, fiberglass, hard rubber, etc.
TO START AND STOP SAW
1. Make sure power circuit voltage is the same as shown on the specification plate on the saw.
Connect saw to power circuit.
2. Hold saw firmly. Squeeze trigger switch (A) Fig. 1, to start motor. Release trigger to stop motor.
VARIABLE SPEED
The saw is equipped with a variable speed control (0 to 2600 SPM). As the switch trigger is squeezed, the
speed of the saw blade increases.
The lower speeds are recommended for most metal cutting, while the higher speeds are recommended
for wood. A few practice cuts at various speeds (on scrap material), will aid you in choosing the best speed
for obtaining the desired results on your application.
HOW TO HOLD SAW
Hold saw as shown in Fig. 2. The gear housing, intermediate plate, blade and pivoting guide shoe may be
made live if the blade cuts into live wiring within a wall.
TO PREVENT ACCIDENTAL ELECTRICAL SHOCK THE SAW MUST BE
HELD AS SHOWN IN FIG. 2, AND MUST HAVE THE RUBBER FRONT
HOUSING COVER PROPERLY INSTALLED AND NOT DAMAGED.
SELECTING THE BLADE
For best performance, longer blade life, and smoother cut, select the proper blade for the job.
When cutting metal always select a blade which will allow at least three teeth to be engaged in the
thickness of material.
INSTALLING THE BLADE
Model SKE 2902 VV with Quik-Change™ Blade Clamp
1. The reciprocating shaft must be fully extended to permit access to the Quik-Change™ blade release
collar (A) Fig. 4. If necessary, gently squeeze the trigger switch to move the reciprocating shaft to its
outermost position (as shown in Fig. 4).
DISCONNECT TOOL FROM POWER SOURCE.
2. Pivot the guide shoe (B) Fig. 4, forward to improve access to the blade clamp.
3. To open the blade clamp: rotate and hold the blade release collar (A) Fig. 5, counterclockwise (as
viewed from the front of the saw).
4. Insert the blade into the clamp until it bottoms. Allow the release collar to rotate clockwise to lock the
blade in place (Fig. 6).
5. To remove blade: repeat steps 1 thru 3, and pull blade from blade clamp (while the release collar is
being held in the open position).
NEVER TOUCH BLADE IMMEDIATELY AFTER USE, AS IT MAY BE
EXTREMELY HOT.
NOTES: If the blade clamp collar resists rotation to remove a blade, work the blade up and down
while rotating the clamp (in a counterclockwise direction).
If the blade breaks leaving nothing to grasp (to pull it from the clamp), it may be necessary to use
another blade as a tool to aid in removing the broken piece (see Fig. 7). While holding the release
collar in the open position, use the tip of another blade to "hook" the broken piece and pull it from
the clamp. (A thin, fine-toothed, metal-cutting blade works best.)
WARNING
WARNING
WARNING
SKD.book Seite 9 Dienstag, 29. August 2006 8:42 20
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Flex ske 2902 vv at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Flex ske 2902 vv in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info