Manual First Degree E316 Fluid Rower (page 27 of 32) (English)

671439

Zoom out

Zoom in

1/32

Troubleshooting

Fault Probable Cause Solution

Water changes

color or becomes

cloudy.

Rower is in direct

sunlight or has not

had water

treatment.

Change rower location to reduce direct

exposure to sunlight. Add water treatment

or change tank water as directed in the

water treatment section of this manual.

Consider using distilled water to refill tank.

Rowing stroke

return is too light.

Bungee not under

enough tension.

Open rear Perspex cover, cut bungee tie

wrap . Tighten by small increments using

the bungee tie off tab point and test

tension by allowing the rowing handle to

return to its furthest point forward while

still having some slight tension. Note light

fraying of the bungee cord is normal.

Rower rocks from

side to side when

sitting on floor

Front/Rear frame

levelers need

adjusting

Adjust the front two frame levelers or rear

leg levelers until stability is reached. Note:

It is normal for the lower rear leveler to

rest slightly off the floor.

Front of rower lifts

slightly during

vigorous rowing.

Lower rear frame

leveler too high.

Check to see that frame tensioning bolt is

tightened properly. Lower rear frame

leveler should be approx. 5mm off the

ground.

Computer screen

illuminates, but

does not register

when rowing.

Loose or failed

connection/Sensor

gap too wide (see

erratic computer

display).

Check that the computer lead is connected

properly. If connected properly check

sensor gap. Contact your local service

center if this fails to address the problem.

The Rower comput-

er does not illumi-

nate after battery

installation.

Batteries installed

incorrectly or need

replacing.

Reinstall batteries in correct position and

try again. If the LCD screen fails to

illuminate, try rotating the batteries

slightly in the computer. If this fails,

contact your local service center.

The Rower comput-

er display is erratic

while displaying

SPM and 500meter

times.

Gap between

sensor and

magnetic ring is

too wide.

Adjust sensor location using rear sliding

adjustment located inside rear Perspex

cover.

Excessive frame flex

during hard rowing.

Frame Tension

Cable is too loose

Loosen frame tension cable Retaining Nut

and tighten cable until taut.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of First Degree E316 Fluid Rower in the language / languages: English as an attachment in your email.

The manual is 2,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

First Degree E316 Fluid Rower Manual

Product: