Manual First Alert PRO8810-600CA (page 25 of 47) (English)

795187

Zoom out

Zoom in

1/47

Page 25

Pan tilt zoom...PTZ

Pan/Tilt/Zoom (PTZ) Setup:

Note: Consult the instruction manual of your PTZ

camera for complete information about your camera,

including protocol, baud rate and parity settings before

beginning setup. Enter these settings in the DVR.

STEP 1: Connect your PTZ Camera to this DVR

Connect a PTZ camera to the BNC and DC power cables. Also,

connect the communication cable from the PTZ camera to the

485A (TX, +) and 485B (RX, -) control inputs to the PTZ block on

the back of the DVR. Note there is only one set of PTZ control

inputs (485A & 485B), however multiple PTZ cameras can be set

up by making parallel connections. See diagram for details and

see “PTZ Camera Setup” Info box for additional information.

PTZ Camera Setup

NOTE: It is recommended for best results to use

120Ω shielded twisted pair cable of a sufﬁcient

gauge to meet your application length. 18 to 22

gauge is usually sufﬁcient. In addition, be sure to

only install the 120Ω terminating resistor that comes with your

PTZ camera in the last parallel connected camera. Keeping that

resistor in all cameras can possibly degrade the signal and can

cause unexpected or loss of operation and control.

Step 2: Conﬁgure PTZ Communication Settings

To access this menu, from the setup menu click DEVICE. Then PTZ.

This will bring up the PTZ setup screen. PTZ setting options for each

camera can be selected independently for each camera channel

1. Select the appropriate channel connected to the PTZ camera using

the drop down

2. Under ADDRESS, enter an address from 001–255 using the virtual

keyboard

3. Under protocol, select the appropriate protocol based on the

setting of the camera using the drop down menu (PELCO-D,

PELCO-P, PELCO-D EXT, PELCO-P EXT, PELCO-D-3)

4. Under BAUD rate, select 1200, 2400, 4800, 9600 as set in the PTZ

camera

5. Click OK to conﬁrm settings. Click EXIT to leave screen without

making changes

LEFT/RIGHT, UP/DOWN, IRIS ZOOM, FOCUS ZOOM and

ZOOM EXCHANGE will reverse the actions taken when

moving or zooming the camera. For example movement

to the left, becomes movement to the right and movement

to zoom in is reversed to movement to zoom out.

Note: Changes to the PTZ setup screen take place immediately.

However, in the event of a power failure, the settings can

revert to the previous settings. It is recommended to perform

a power down and restart through the drop down menu to

save changes in order for the system to operate with these

changed PTZ setting should a power failure occur.

Pan tilt zoom...PTZ continued

Install 120 Ω

terminating

resistor in last

camera only

AB AB AB

PTZ Inputs Conguration

RS485

– +

–

ADVANCED OPERATION

PTZ

PTZ Setup Screen

PTZ Manual Control Screen

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of First Alert PRO8810-600CA in the language / languages: English as an attachment in your email.

The manual is 2.9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

First Alert PRO8810-600CA Manual

Product: