778505
25
Zoom out
Zoom in
Previous page
1/150
Next page
Colour Material Symbol
Yellow Wood
Red Laminate, mineral ma
terial
HPL/TRESPA
®
Green Plaster- and cement-
bonded chipboard and
fibreboard
Blue Aluminium, plastic
"$3:-
7.5 Changing the saw blade
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
Remove the saw blade
Swivel the machine to 0° before replacing
the saw blade and adjust the maximum cut
ting depth.
Turn the lever [5-2] as far as it will go.
Slide the safety lock [5-1] upwards and
push the saw unit downwards until it clicks
into place.
Loosen the screw [5-5] using the Allen
key [5-3].
Remove the saw blade [5-7].
Inserting the saw blade
WARNING! Check the screws and flange for
contamination and only use clean and undam
aged parts.
Insert the new saw blade.
WARNING! The direction of rotation of the
saw blade [5-8] and saw [5-6] must match.
Serious injuries may occur in the event of
non-compliance.
Insert the outer flange [5-9] so that the pin
engages in the recess on the inner flange.
Tighten the screw [5-5].
Reposition the lever [5-2].
7.6 Fitting the viewing window/splinter
guard
The viewing window (transparent) [6-1] pro
vides a view of the saw blade and optimises
dust extraction.
With 0° cuts, the splinter guard (green) [6-2]
also improves the quality of the cutting edge of
the sawn-off workpiece on the upper side.
Insert the splinter guard [6-2].
Screw the rotary knob [6-3] through the
long hole in the splinter guard.
Make sure that the nut [6-4] is seated se
curely in the splinter guard.
CAUTION! Only use the rotary knob sup
plied with your plunge-cut saw. The rotary
knob of another saw may be too long and
jam the saw blade.
Sawing a splinter guard
You must bed in the splinter guard before using
it:
Set the machine to maximum cutting depth.
Set the machine speed to 6.
Place the machine for sawing the splinter
guard on a test piece of wood.
7.7 Dust extraction
WARNING
Heath hazard posed by dust
Always work with an extractor.
Comply with national regulations.
Festool mobile dust extractor
A Festool mobile dust extractor with a suction
hose diameter of 27/32 mm or 36 mm (36 mm
recommended due to the reduced risk of clog
ging) can be connected to the extractor connec
tor .
The adapter on a 27 diameter suction hose is
inserted into the angle adapter . The adapter on
a 36 diameter suction hose is inserted over the
angle adapter .
CAUTION! A static charge may build up if no
antistatic suction hose is used. The user may
receive an electric shock and the power tool's
electronics may be damaged.
8 Working with the electric
power tool
When working on the machine, observe
all of the safety warnings that are listed
at the start as well as the following rules:
English
25
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TS 55 FQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TS 55 FQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info