778505
24
Zoom out
Zoom in
Previous page
1/150
Next page
7 Settings
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
7.1 Electronics
The machines TS 55 FEBQ, TS 55 FEQ come
with full-wave electronics with the following
properties:
Smooth start-up
The electronically controlled smooth start-up
function ensures that the power tool starts up
smoothly.
Constant speed
The motor speed is electronically kept con
stant. This ensures a uniform cutting speed
even when under load.
Speed control
You can continuously adjust the speed within
the speed range using the adjusting
wheel [1-10] (see "Technical data"). This ena
bles you to optimise the cutting speed to suit
each surface.
Speed range per material
Solid wood (hard, soft) 6
Chipboard and hardboard 3–6
Laminated wood, blockboard, veneered
and laminated panels 6
Laminate, mineral materials 4–6
Plaster- and cement-bonded chipboard
and fibreboard 1–3
Aluminium panels and profiles up to
15 mm 4–6
Plastics, fibre-reinforced plastics, paper
and fabric 3–5
Acrylic glass 4–5
Current limiting
Current limiting prevents excessive current
consumption under extreme overload, which
can lead to a decrease in the motor speed. The
motor immediately restarts after the load is re
moved.
Brake
The saw TS 55 FEBQ comes with an electronic
brake. The saw blade is stopped electronically
within approximately two seconds of switching
off the machine.
Temperature cut-out
The power supply is restricted and the speed
reduced if the motor exceeds a certain temper
ature. The power tool continues operating at re
duced power to allow the ventilator to cool the
motor quickly. The power tool starts up again
automatically once the motor has cooled suffi
ciently.
7.2 Adjusting the cutting depth
The cutting depth can be set at 0 – 55 mm at the
cutting depth stop [3-1].
The saw unit can now be pushed downwards as
far as the cutting depth that is set.
Cutting depth without guide rail
max. 55 mm
+FS
Cutting depth with FS guide rail
max. 51 mm
7.3 Setting the cutting angle
between 0° and 45°:
Unscrew the rotary knobs [4-1].
Swivel the saw unit to the desired cutting
angle [4-2].
Tighten the rotary knobs [4-1].
Both positions (0° and 45°) are set at the
factory and can be readjusted by the cus
tomer service team.
When making angled cuts, slide the view
ing window/splinter guard to the highest
position.
To undercut -1° and 47°:
Swivel the saw unit to the end position (0°/
45°) as described above.
Pull out the release button [4-3] slightly.
For -1° undercuts, also pull the release
button [4-4].
The saw unit engages in the -1°/47° position.
Tighten the rotary knobs [4-1].
7.4 Selecting the saw blade
Festool saw blades are identified by a coloured
ring. The colour of the ring represents the ma
terial for which the saw blade is suited.
Refer to the necessary saw blade data (see sec
tion 3.1).
English
24
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TS 55 FQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TS 55 FQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info