778606
17
Zoom out
Zoom in
Previous page
1/93
Next page
Close the clamping lever.
7.2 Adjusting the saw blade guidance
To be better able to guide the saw blade, pen
dulum jigsaws have an additional carbide
guide [3-2] immediately above the workpiece.
Tighten the screw [3-3] using the allen
key [1-5] until the jaws are almost touching
the saw blade.
It must be possible to move the saw blade
slightly.
7.3 Inserting the splinterguard
The splinterguard prevents the edges of the
material from splintering during the cut, even
at the end where the saw blade exits the mate
rial.
Switch off the machine and slide the splin
terguard [4-3] onto the guide [4-2] and up
to the saw blade.
Switch on the jigsaw.
With the machine running, push the splin
terguard in on a flat plane until it is flush
with the front edge of the saw table. This
cuts into the splinterguard.
To guarantee reliable operation of the
splinterguard, it must seal tightly on both
sides of the saw blade. A new splinter
guard should therefore be fitted after ev
ery saw blade change to guarantee splint
er-free cuts.
7.4 Inserting the chip guard
The chip guard prevents chips from flying away
and improves the efficiency of the chip extrac
tion system.
Insert the chip guard [2-10] between the
saw table and the clamping lever.
Gently slide the chip guard back until it en
gages.
7.5 Adjusting the saw table
For bevel cuts, the saw table can be swivelled
to either side by up to 45°.
Remove the chip guard and the splinter
guard.
Open the clamping screw [4-1] with the al
len key .
Slide the saw table forwards by approx.
5 mm.
Set the desired inclination using the
scale [5-2].
Tighten the clamping screw [4-1].
To saw close to the edges, the saw table can be
shifted backwards.
Remove the chip guard and the splinter
guard.
Open the clamping screw [4-1] with the al
len key .
Slide the saw table into the rear position so
that the centring mandrel [5-1] slots into
the opening [5-3].
Tighten the clamping screw [4-1].
7.6 Adjusting the pendulum stroke
The pendulum stroke on pendulum jigsaws can
be adjusted to machine different materials with
the correct rate of advance. Select the required
setting using the pendulum stroke switch [1-6]:
Position 0 = pendulum stroke off
Position 3 = maximum pendulum stroke
Recommended pendulum stroke setting
Hardwood, softwood, chipboard, wood
fibreboard 1 - 3
Blockboard, plywood, plastic 1 - 2
Ceramics 0
Aluminium, non-ferrous metals 0 - 2
Steel 0 - 1
7.7 Stroke speed control
The stroke rate can be continuously adjusted
between 1000 and 2900 min-1 using the adjust
ing wheel [1-3; 2-4]. This enables you to opti
mise the cutting speed to suit the respective
material.
Recommended stroke speed (position of the
adjusting wheel)
Hard and soft wood, blockboard, ply
wood, chipboard 6
Fibreboard 4 - 6
Plastic 3 - 6
Ceramic, aluminium, non-ferrous
metals 3 - 5
Steel 2 - 4
7.8 Extraction
WARNING
Health risk due to dust
Always work with an extractor.
Comply with national regulations.
The extraction adapter [2-5] allows jigsaws to
be connected to a dust extractor (hose diameter
27 mm).
English
17
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool Trion PS 300 EQ - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool Trion PS 300 EQ - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 1.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info