574934
16
Zoom out
Zoom in
Previous page
1/90
Next page
16
TI 15
GB
Turn the clamping ring as far as the stop to se-
cure the adapter.
Angle attachment DD-AS [7]
Drilling and screwing at right angle to machine
(partly as an accessory).
Eccentric attachment DD-ES [8]
Screwdriving near edges with bits according to ISO
1173 (partly as accessory).
9 Working with the machine
9.1 Operating modes
Depending on the tool holder / adapter selected,
the machine is operated as follows:
9.2 On/Off switch [1-2]
Press = ON, release = OFF
Depending on the pressure applied to the ON/
OFF switch the speed/impact rate can be con-
trolled continuously.
The LED bulb
[1-4]
lights up when the ON/OFF
switch is pressed
[1-2]
.
9.3 Bit depot [1-1]
Magnetic, for storing bits and bit holders.
9.4 Belt clip [1-9]
For short-term fixing of the device to work attire:
can be moved to the right or left or can also be de-
tached from the battery pack.
9.5 Acoustic warning signals
Acoustic warning signals sound and the machine
switches off in the following operating states:
10 Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at:
www.festool.com/Service
Use only original Festool spare parts!
Order No. at:
www.festool.com/Service
Note the following information:
Keep the ventilation slits on the machine free and
clean to ensure adequate cooling.
Keep the contacts on the machine, charger and
battery pack clean.
Information on battery packs
Store in a cool, dry place at a temperature be-
tween 5 °C and 25 °C.
Protect battery packs from moisture, water and
heat.
Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. Danger of deep discharge!
If you intend to store li-ion battery packs for lon-
ger periods without use, you should charge them
to 40 % capacity (approx. 15 min charging time).
Screwing with impact
WH-CE CENTROTEC tool chuck (see
Chapter CENTROTEC tool chuck [4])
Screwing and drilling without impact
TI-FX adapter (see Chapter TI-FX adapter
[6])
DD-AS elbow adapter
DD-ES eccentric attachment
DD-DC screwdriver attachment
– BF-TI 13 chuck (see Chapter BF-TI 13
chuck [5])
WARNING
Risk of injury
Only place the machine on the nut/screw when
switched off.
Battery flat or machine over-
loaded.
Change the battery.
Place the machine under reduced
stress.
Machine is overheating.
You must allow the machine to
cool before using again.
LiIon battery pack is faulty or has
overheated.
Once the battery pack has cooled,
perform a functional check using
the charger.
WARNING
Risk of injury, electric shock
Always disconnect the battery pack from the
machine before any maintenance or care work!
All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TI 15-14.4 V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TI 15-14.4 V in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 17,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info