Manual Festool RO 90 DX FEQ ROTEX (page 14 of 83) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

498080

Zoom out

Zoom in

1/83

ROTEX

Temperature cut-out

The machine power supply is limited and the

speed reduced if the motor exceeds a certain

temperature. The machine continues operat-

ing at reduced power to allow the ventilator

to cool the motor quickly. If the machine

temperature exceeds the maximum permit-

ted value for longer periods, the machine

switches off completely after approx. 40 sec-

onds and can only be switched on again once

the motor has cooled sufficiently.

7.2 Setting sanding motion [3]

The change-over switch

[1-2]

can be used

to set three different sanding motions.

This change-over can only be carried out

with the sanding pad stationary because

the switch is locked during operation.

Coarse sanding, polishing - ROTEX rota-

ry motion

The Rotex rotary motion is a combi-

nation of rotary and eccentric mo-

tions. This position is selected for

sanding with high output (coarse

sanding) and polishing.

Fine sanding - eccentric motion

This position is selected for sanding

with low output for a scratch-free

surface (fine sanding).

Triangular sanding and pad change [4]

This position is used for sanding

with the delta sanding pad and slat

sanding pad; the rotary motion is

blocked.

You can change the sanding pad in

this position.

The stop rod

[1-8]

blocks the in-

stallation of the sanding pad in the

change-over switch positions ROTEX rota-

ry motion and eccentric motion.

7.3 Changing sanding/polishing pad

[5]

Only use sanding and polishing pads that

are suitable for the maximum speed spec-

ified.

Tuned to the surface being processed, the

machine can be equipped with two sanding

pads of different hardnesses.

Hard:

Coarse and fine sanding on surfaces.

Sanding edges.

Soft:

Universal for coarse and fine sanding,

for flat and convex surfaces.

When the interface pad

[1-12]

is fitted on

the sanding pad, strength is reduced = extra

soft.

Following the sanding pad change, switch

the change-over switch

[1-2]

to the de-

sired sanding motion.

7.4 Changing sanding pad [6]

The delta sanding pad DSS-GE-STF-RO90

can be used for sanding close to borders, in

corners or on edges. The slat sanding pad

LSS-STF-RO90 can be used for sanding in

narrow gaps, e.g. louvres.

Observe the following instructions:

Work in corners and on edges tends to sub-

ject the tip to increased stress and results in

increased heat development. In such cases,

work with reduced contact pressure.

Delta sanding pad DSS-GE-STF-RO90

[7]

If the front tip of the StickFix pad

[7-1]

your delta sanding pad is worn, take it off

and turn it 120°.

Slat sanding pad LSS-STF-RO90 [8]

If the StickFix coating of the slat sanding pad

is worn, the complete table can be replaced.

Open the screws to do this

[8-1]

7.5 Attaching sanding accessories

The suitable StickFix sandpaper and StickFix

sanding cloth can be attached quickly and

simply to the StickFix sanding pad.

Press the self-adhesive sanding accessory

onto the sanding pad

[1-7]

7.6 Attaching polishing accessories

To prevent damage, PoliStick accessories

(polishing sponges, polishing felt, sheepskin)

must only be used on the special polishing

pad.

Press the self-adhesive polishing accesso-

ry onto the sanding pad

[1-9]

7.7 Dust extraction

WARNING

Dust hazard

Dust can be hazardous to health. Always

work with a dust extractor.

Always read applicable national regula-

tions before extracting hazardous dust.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool RO 90 DX FEQ ROTEX in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 25,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool RO 90 DX FEQ ROTEX Manual

Product: