Manual Festool PSBC CARVEX 420 EB (page 21 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

497995

Zoom out

Zoom in

1/132

C A R V E X

Damaged safety devices and components

must be repaired or replaced in a recognised

specialist workshop, unless otherwise indicat-

ed in the operating manual.

Observe the following instructions:

– Keep the air slits on the machine and the

charger free and clean to ensure adequate

cooling.

– Keep the contacts on the machine, charger

and battery pack clean.

– Check the guidance roller regularly for wear.

– Regularly remove dust deposits from the

chip guard.

– Regularly clean the base runner to prevent

scratches and cores on the surface.

Information on battery packs

– Where possible, store the battery pack in a

cool, dry place at a temperature between

5°C and 25 °C.

– Battery packs are most efficient at temper-

atures between 20 °C and 30 °C.

– Protect the battery pack from moisture, wa-

ter and heat.

– Significantly shorter operating times after

each charge indicate that the battery pack is

worn and should be replaced with a new

one.

– The LiIon battery pack is fully compatible

with the charger! Integrated electronics pre-

vent overloading and overheating during the

charging process.

– Do not leave flat battery packs in a charger

disconnected from the mains power supply

for longer than one month. There is a risk of

total discharge and the maximum power of

the battery pack may decrease.

– Store the battery pack in its packaging to re-

duce the risk of short circuits..

– If LiIon battery packs are to be stored for

long periods without use, they should be

charged to 40 % capacity (approx. 15 mins.

charging period).

10 Accessories

The order numbers of the accessories and

tools can be found in the Festool catalogue or

on the Internet under "www.festool.com".

10.1 Saw blades, other accessories

In order to saw different materials quickly and

cleanly, Festool offers saw blades for all appli-

cations that are specially designed for your

Festool jigsaw.

10.2 Sawing with special base runners

The special base runners protect high-quality

surfaces against scratches and scores.

Press in the base runner at position

[7-1]

At the same time, push the base runner

forwards.

Mount another base runner and push it to

the rear until it engages.

10.3 Sawing with the angle table

The angle table WT-PS 400 is used for cutting

pipes or interior and exterior angles up to 45°.

Dust extraction is not possible when

sawing with the angle table!

Installing the angle table

Remove the saw base

[1-10]

, (see chap-

ter

7.4

Position the angle table against the saw

base support.

Close the lever

[1-8]

Ensure that the angle table is firmly seated in

the guide.

Setting the angle

Turn the adjusting wheel

[8-1]

to select

the required angle.

You can select the angles -45°, 0° and +45°

on the scale

[8-2]

For 90° cuts, we recommend setting the

angle table to a small negative angle to

guarantee smooth operation.

10.4 Sawing with the adaptation table

The adaptation table ADT-PS 400 is used for

fitting your jigsaw on the Festool guide rail and

the circle cutter KS-PS 400.

With guide rail and circle cutter:

not exceed max. material thickness of

20 mm and always use cross-set saw

blades (FSG).

Installing the adaptation table

Remove the saw table

[1-10]

, (see chap-

ter

7.4

WARNING

Sawing cutting depths

Risk of injury

Select the saw blade length and cutting

depth so that the saw blade remains

plunged in the workpiece.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSBC CARVEX 420 EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool PSBC CARVEX 420 EB Manual

Product: