497985

Festool PS TRION 300 Q Manual

14
Zoom out
Zoom in
Previous page
1/79
Next page
14
TRION
GB
push base runner to rear position so that the
centring pin
[5-1]
fits in the opening
[5-3]
,
tighten locking screw
[4-1]
.
7.7 Adjusting the pendulum stroke
In order to process different materials with an opti-
mum feed movement the pendulum jigsaws have
an adjustable pendulum stroke. Select the desired
setting with the pendulum stroke switch
[1-5]
:
setting 0 = pendulum stroke off
setting 3 = maximum pendulum stroke
7.8 Adjusting the number of strokes
PSB 300 Q,
PSB 300 EQ
You can regulate the number of strokes steplessly
between 1000 and 2900 min
-1
using the adjusting
wheel
[1-2; 2-3]
. This enables you to optimise the
cutting speed to suit the material.
8 Working with the machine
8.1 Free hand according to the scribe mark
The triangular shape of the splinterguard
[4-3]
shows the cutting line of the saw blade and thus fa-
cilitates cutting to a scribe mark.
8.2 Plunge cutting without pilot drilling
The base runner must be in the front position for
plunge cuts in timber materials (basic setting, see
Figure
[1]
).
Place saw on the front edge of the runner.
Set saw to maximum no. of strokes and pendu-
lum stroke setting 3 and start the plunge cut
into the workpiece (Figure
[6]
).
9 Service and maintenance
Damaged safety devices and components must be
repaired or replaced in a recognised specialist
workshop, unless otherwise indicated in the oper-
ating manual.
To ensure constant air circulation, always keep the
cooling air openings in the motor housing clean and
free of blockages.
10 Accessories
The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
10.1 Festool guide system FS
The use of the Festool guide system FS (Figure
[7]
)facilitates the production of straight and precise
cuts, particularly with material thicknesses up to
20 mm. The jigsaw is hereby placed in a guide stop
[7-1]
order no. 490031) and guided along the guide
rail in this. The guide stop has two adjustable limit
stops
[7-2]
for a setting free from play. Use only
crossed saw-blades when utilising the guide stop.
We recommend Festool saw blade S 75/4 FSG.
10.2 Parallel guide
Use the parallel guide (order no. 490119) to guide
the jigsaw parallel to the workpiece edge. The par-
allel guide can be fitted on both sides of the base
runner:
Slide clamping clip
[8-1]
onto the base runner
from the front,
insert parallel guide
[8-2]
through the clamping
clip from the side to the desired position,
tighten rotary knob
[8-3]
.
Recommended settings of the pendulum
stroke
Hard and soft wood,chip board, wood
fibre board
1 - 3
Wood core plywood, plywood, plastics 1 - 2
Ceramic 0
Aluminium, NF metals 0 - 2
Steel 0 - 1
Recommended number of strokes (adjusting
wheel setting)
Hard and soft wood, wood core plywood,
plywood, chip board
6
Wood fibre boards 4 - 6
Plastics 3 - 6
Ceramic, aluminium, NF metals 3 - 5
Steel 2 - 4
WARNING
Risk of injury
Always secure the workpiece in such a manner
that it cannot move while being machined.
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing maintenance work on
the machine!
All maintenance and repair work which requires
the motor housing to be opened must only be
carried out by an authorised service workshop.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PS TRION 300 Q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PS TRION 300 Q in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info