497985
13
Zoom out
Zoom in
Previous page
1/79
Next page
TRION
13
GB
Connecting and detaching the mains power cable
[1-3]
see Fig.
[2a]
.
PS 300 Q, PS 300 EQ
The power tool has a slide switch to switch the tool
on and off (I = ON, 0 = OFF).
PSB 300 Q, PSB 300 EQ
The power tool have a push button switch
[2-2]
to
switch the tool on and off.
The locking button
[2-1]
can be engaged to operate
in continuous mode. Press the switch again to re-
lease the knob.
7 Settings
7.1 Changing tools
Open chuck lever
[3-4]
up to the stop.
Remove fitted saw blade.
Insert new saw blade up to the stop in the saw
blade holder
[3-1]
.
Close chuck lever.
7.2 Adjusting three saw blade guide
The pendulum jigsaws have an additional hard
metal guide
[3-2]
immediately above the workpiece
for a better guidance of the saw blade.
Tighten the screw
[3-3]
with the Allen keyl
[1-4]
until the jaws almost rest against the saw blade.
The saw blade should still be able to be
moved easily!
7.3 Fitting the splinterguard
The splinterguard allows cuts with splinter-free
edges, even on the exit side of the saw blade.
With the tool switched off, fit the splinterguard
[4-3]
on the guide
[4-2]
up to the saw blade,
switch the jigsaw on,
with the tool running, push the splinterguard in
until the splinterguard is flush with the front
edge of the base runner. Thereby the splinter-
guard is cut in.
The splinterguard must lie close to the saw
blade on both sides to ensure its reliable opera-
tion. Thus, a new splinterguard should be fitted
every time the saw blade is changed to ensure
splinter-free cuts.
7.4 Fitting the chip guard
The chip guard prevents chips from flying off and
improves the efficiency of the chip extractor.
Insert the chip guard
[2-8]
between the base
runner and chuck lever,
push back the chip guard with a slight pressure
until it catches in place.
7.5 Dust extraction
Jigsaws can be connected to a dust extractor (hose
diameter 27 mm) using the extractor adapter
[2-4]
.
When working with suction units, always use a
splinterguard in order to prevent the suction
channels becoming blocked.
Insert the extractor adapter into the rear hole of
the base runner in so that the hook
[2-6]
catch-
es in the notch
[2-7]
.
Press the lever
[2-5]
to remove the extractor
adapter.
7.6 Adjusting the base runner
The base runner can be swivelled to both sides by
up to 45° for bevel cuts.
Remove chip guard and splinterguard,
release locking screw
[4-1]
with Allen key
[1-
4]
,
push base runner approx. 5 mm forwards,
set desired inclination according to the scale
[5-
2]
,
tighten locking screw
[4-1]
.
The base runner can be moved back for sawing
close to edges.
Remove chip guard and splinterguard,
release locking screw
[4-1]
with Allen key
[1-4]
,
WARNING
Risk of injury, electric shock
Always pull the mains plug out of the socket be-
fore performing any type of work on the ma-
chine!
WARNING
Risk of injury, electric shock
Always pull the mains plug out of the socket be-
fore performing any type of work on the ma-
chine!
WARNING
Dust hazard
Dust can be hazardous to health. Always work
with a dust extractor.
Always read applicable national regulations be-
fore extracting hazardous dust.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PS TRION 300 Q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PS TRION 300 Q in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info