383568

Festool ps 300 ebq Manual

16
Zoom out
Zoom in
Previous page
1/86
Next page
16
TRION
GB
Damaged safety devices and components
must be repaired or replaced in a recognised
specialist workshop, unless otherwise indi-
cated in the operating manual.
To ensure constant air circulation, always
keep the cooling air openings in the motor
housing clean and free of blockages.
10 Accessories
Use only original Festool accessories and
Festool consumable material intended for
this machine because these components are
designed specifically for the machine. Using
accessories and consumable material from
other suppliers will most likely affect the
quality of your working results and limit any
warranty claims. Machine wear or your own
personal workload may increase depending
on the application. Protect yourself and your
machine, and preserve your warranty claims
by always using original Festool accessories
and Festool consumable material!
The order numbers of the accessories and
tools can be found in the Festool catalogue or
on the Internet under "www.festool.com".
10.1 Festool guide system FS
The use of the Festool guide system FS (Fig-
ure [7])facilitates the production of straight
and precise cuts, particularly with material
thicknesses up to 20 mm. The jigsaw is here-
by placed in a guide stop [7-1] order no.
490031) and guided along the guide rail in
this. The guide stop has two adjustable limit
stops [7-2] for a setting free from play. Use
only crossed saw-blades when utilising the
guide stop. We recommend Festool saw
blade S 75/4 FSG.
10.2 Parallel guide
Use the parallel guide (order no. 490119) to
guide the jigsaw parallel to the workpiece
edge. The parallel guide can be fitted on both
sides of the base runner:
X
Slide clamping clip [8-1] onto the base
runner from the front,
X
insert parallel guide [8-2] through the
clamping clip from the side to the desired
position,
X
tighten rotary knob [8-3].
10.3 Circle cutter
The circle cutter (order no. 490118) can be
used to produce circular cuts with a diameter
between 120 and 720 mm. The circle cutter
can be fitted on both sides of the base run-
ner:
X
Slide clamping clip [8-1] onto the base
runner from the front,
X
insert circle cutter [8-4] through the
clamping clip from the side to the desired
position,
X
tighten rotary knob [8-3],
X
insert circle tip [8-5] in the rear bore hole
of the circle cutter.
10.4 Festool CMS
By fitting the jigsaws in the Festool Systems
CMS you end up with a semi-stationary
bench-mounted saw for profile cuts. Further
information can be fond in the CMS brochure.
10.5 Saw blades, other accessories
In order to saw different materials quickly
and cleanly, Festool offers saw blades for all
applications that are specially designed for
your Festool jigsaw.
11 Disposal
Do not throw the power tool in your house-
hold waste! Dispose of machines, accesso-
ries and packaging at an environmentally re-
sponsible recycling centre. Observe the valid
national regulations.
EU only:
European Directive 2002/96/EC
stipulates that used electric power tools must
be collected separately and disposed of at an
environmentally responsible recycling cen-
tre.
12 Warranty
We offer a warranty for material and produc-
tion defects for all our tools in accordance
with the locally applicable legal provisions,
but for a minimum of 12 months. Within the
EU member states, the warranty period is 24
months (verification through invoice or deliv-
ery note). Damage caused by the operator,
natural wear, overloading, incorrect handling
or through the use of the equipment not
specified in the operating manual, or damage
which was known at the time of purchase, is
not covered by the warranty. Furthermore,
damage caused by the use of non-original
accessories and consumable materials (e.g.
sanding pads) is also excluded.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ps 300 ebq at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ps 300 ebq in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info