778612
32
Zoom out
Zoom in
Previous page
1/196
Next page
32
9.2 Using the machine as table saw with
sliding function
9.2a Cross cuts
fPlace the saw blade in the back table position,
see section 8b.
fUse the preset profile setting rail as a cross-
wise or angle ruler (fig. 3) to position the
workpiece and hold it in place. Fastening
clamps (not included) can be inserted into the
groove [3-8] to secure the workpiece.
Make the saw cut:
fFirst release the saw lock by turning the rotary
knob [2-6] anticlockwise.
fPull the saw forward using the same rotary
knob [2-6].
fAfter completing the cut, move the saw unit
right back to its starting position before re-
moving the workpiece from the preset profile
setting rail.
NOTE
To ensure that the control elements are easy to
access for adjusting the saw settings, the saw
can be locked in the middle position by push-
ing the notch lever [1-9] down. Turn the rota-
ry knob [2-6] anticlockwise to release the lock
again.
9.2b Angled cuts
The mitre angle of the saw blade needs to be ad-
justed for angled cuts, see section 8.7. The pre-
set profile setting rail is on the right-hand side
of the table.
The preset profile setting rail needs to be adjust-
ed for mitre cuts, see section 8.10.
9.3 Push stick
Place the push stick [11-2] in the accessory
holder [11-4] when not in use.
10 Service and maintenance
WARNING
Risk of accident, electric shock
fAlways disconnect the mains plug before
maintaining, servicing or making any kind of
adjustment.
fAll maintenance and repair work which re-
quires the motor housing to be opened should
always be carried out by an authorised ser-
vice workshop.
fDamaged safety devices and components
must be repaired or replaced in a recognised
specialist workshop in accordance with reg-
ulations, unless otherwise indicated in the
operating manual.
Customer service and repairs: must only
be carried out by the manufacturer or
service workshops. Find the nearest ad-
dress at:
www.festool.co.uk/service
EKAT
1
235
4
Always use original Festool spare parts.
Order no. at:
www.festool.co.uk/service
The machine is equipped with special self-dis-
connecting carbon brushes. If they wear out, the
power supply is disconnected automatically and
the tool stops.
Maintain your machine regularly to make sure it
functions properly:
-Use an extractor to remove dust deposits.
- Keep the guide rods clean and grease them
regularly.
- Keep the toothed gears behind the rotary han-
dle [2-3] clean.
- Replace worn or damaged table inserts [1-7].
- If wood chips block the extraction channel on the
bottom guard, unscrew the rotary knob [5-8]
and move the flap [5-6] approx. 8 mm to
open up a gap so that the blockage can be
removed.
- If the blockage is serious or the saw seiz-
es when the initial cut is made, use the hex
key to unscrew the fasteners [5-7] so that the
flap [5-6] can be opened completely. Close the
flap again prior to use.
- After completing work, wind the power ca-
ble [11-1] around the accessory holder [11-4].
- A damper allows the saw unit to retract even-
ly along the entire cutting length. If this is not
P R E C I S I O - GB
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PRECISIO CS 70 EG - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PRECISIO CS 70 EG - 2020 in the language / languages: All languages as an attachment in your email.

The manual is 3.42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info