778612

Festool PRECISIO CS 70 EG - 2020 Manual

31
Zoom out
Zoom in
Previous page
1/196
Next page
31
P R E C I S I O - GB
fUse the preset profile setting rail as a length-
wise ruler (fig. 1) to guide the workpiece.
fYou can adjust the cutting width using the
scales.
fGuide the workpiece by hand, keeping your
arms away from the saw blade’s centre line.
fUse the push stick [11-2] to guide the work-
piece accurately past the saw blade.
fPlace the push stick in the accessory hold-
er [11-4] when not in use.
9.1b Angled cuts
The mitre angle of the saw blade needs to be
adjusted for angled cuts, see section 8.7.
9.1c Non-through cuts
If the guard has been removed, the riving knife
can be adjusted by firmly pulling by two locking
positions. The riving knife is used in the upper
locking position for all applications, except for
non-through cuts.
Before starting work
fRemove the upper guard [6-4].
fMove the riving knife [6-1] into the lower lock-
ing position by pushing it down firmly.
Creating non-through cuts
When executing non-through cuts, pay particular
attention that the tool is guided precisely. To do
this, push the workpiece down firmly onto the
table. Select the cutting sequence so that the
workpiece side already sawed out is not the fence
side (risk of kickback).
Rabbeting
fSet the cutting depth and fence of the first side
of the rebate.
fCarry out the first saw cut of the rebate by
guiding the workpiece by hand. Keep your
arms away from the saw blade’s centre line.
fUse the push stick [11-2] to guide the work-
piece past the saw blade.
fTurn the workpiece.
fSet the cutting depth and fence of the second
side of the rebate.
fMake the second saw cut of the rebate.
fUse the push stick [11-2] to guide the work-
piece past the saw blade.
Rabbeting on workpieces ≤ 12 mm with a table
saw with sliding function (with the saw blade
locked)
fUse the fence as a cross-cutting fence (fig. 3).
fObserve the operating instruction for cross
cuts (see section 9.2a).
NEVER use the fence as a rip fence when
rabbeting on the short side.
Grooving
fAdjust the cutting depth on the saw blade.
fUse the fence as a guide.
fGuide the workpiece by hand. Keep your arms
away from the saw blade‘s centre line.
fUse the push stick [11-2] to guide the work-
piece past the saw blade.
fRepeat the process until the required grooving
depth is achieved.
After finishing work
fAfter executing the non-through cuts, move
the riving knife [6-1] back into the upper posi-
tion and attach the guard [6-4].
Complicated concealed cut process
fe.g. plunge saws, resawing, dadoing, profile
routing and fluting are not permitted.
9.1d Featherboard
NOTE
Use a featherboard for non-through cuts. Fit the
featherboard on the fence and the table so that the
featherboard pushes the workpiece down firmly
onto the plate during cutting. Featherboards are
not included with the delivery.
9.1e Longitudinal cuts at an angle
fOnly use the left fence when making longitu-
dinal cuts at an angle in material with an edge
length of ≤ 150 mm. This creates more space
between the fence and the saw blade.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PRECISIO CS 70 EG - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PRECISIO CS 70 EG - 2020 in the language / languages: All languages as an attachment in your email.

The manual is 3.42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info