Manual Festool PRECISIO CS 50 EG - 2021 (page 24 of 180) (All languages)

778610

Zoom out

Zoom in

1/180

- When cutting wood, connect the machine to a

dust extractor corresponding to EN 60335-2-69,

dust class M.

- To minimise the release of dust, the machine

should be connected to a suitable dust extractor.

All dust extraction elements (dust extraction

attachments, etc.) must be properly adjusted.

- Never process material that contains asbestos.

- Make sure that you have enough light in the

room or work place.

- When sawing, adopt the correct working posi-

tion:

- At the front on the side of the operator;

- Head-on to the saw;

- Beside the line of cut.

- Use the accompanying push stick to guide the

workpiece accurately past the saw blade.

- Always use the supplied riving knife and the

guard. Ensure that they are set correctly as

described in the operating instructions. If the

riving knife is set incorrectly and components

that are required for safety reasons (such as the

guards) are removed, this may result in serious

injuries.

- Use a suitable device to support long workpieces

and ensure that they are horizontal.

- Pull the plug from the mains power socket be-

fore changing tools and rectifying faults such as

removing trapped splinters.

- Do not remove offcuts or other workpiece parts

from the cutting area while the machine is still

running or before the saw blade stops moving.

- If the saw blade is jammed, switch the machine

off immediately and disconnect the mains plug.

Do not remove the jammed workpiece until you

have done this.

- Cutting rebates or grooves is only permitted

when a suitable protective device has been ﬁtted,

e.g. a protective tunnel over the saw table.

- Reinstall the safety equipment immediately af-

ter work that requires the guard to be removed,

see section 5.2.

- Do not use circular saws for cutting slots

(grooves in workpiece).

- Before transporting the machine, make sure

that the top guard covers the top section of the

saw blade.

- Do not use the top guard as a handle for trans-

portation.

- When not in use, store the push stick in the

accessory holder provided on the machine.

- Use only original Festool accessories and aids.

- Use of your own aids e.g. push stick, rulers, etc.

is not permitted.

- Before commencing work, check that the guard

and splinter guard can move freely and are rest-

ing on the table.

- To prevent the saw blade from overheating or

the plastic from melting, set the correct speed

for the cutting material and do not use excess

pressure when cutting.

- When cutting metal, switch on the saw using a

residual current circuit breaker.

- Check the plug and the cable regularly and

should either become damaged, have them

replaced by an authorised after-sales service

workshop.

- Only for AS/NZS: The tool shall always be sup-

plied via residual current device with a rated

residual current of 30 mA or less.

4.4 Emission levels

Typically, the noise levels that are determined in

accordance with EN 62841 (see EC declaration of

conformity) are as follows:

Sound pressure level LPA = 87 dB(A)

Sound power level LWA = 101 dB(A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection!

- The speciﬁed noise emission levels have been

measured in accordance with the standard test-

ing method and can be used to compare power

tools.

- The speciﬁed noise emission levels can also be

used for making preliminary estimates regard-

ing noise load.

CAUTION

The noise emissions during actual use

of the power tool can differ from the

declared values depending on the ways

in which the tool is used especially what

kind of workpiece is processed.

- Identify safety measures to protect

the operator that are based on an estima-

tion of exposure in the actual conditions

of use (taking account of all parts of the

operating cycle such as the times when

the tool is switched off and when it is run-

ning idle in addition to the trigger time).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool PRECISIO CS 50 EG - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 7.36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool PRECISIO CS 50 EG - 2021 Manual

Product: