778610

Festool PRECISIO CS 50 EG - 2021 Manual

25
Zoom out
Zoom in
Previous page
1/180
Next page
25
4.5 Other risks
In spite of compliance with all relevant design
regulations, dangers may still present themselves
when the machine is operated, e.g.:
- Workpiece parts being thrown off,
- Parts of damaged tools being thrown off,
- Noise emissions,
- Wood dust emissions.
5 Set-up, operation
- When unpacking the tool, remove all transport
inserts.
- Ensure that the floor around the machine is
level, in good condition and free of loose objects
(e.g. chips and offcuts).
5.1 Setting up the machine
The machine can be set up with or without un-
folded legs (fig. 1 and 2).
To unfold the legs, loosen the four rotary
knobs [1-6] all the way. Tighten the four rotary
knobs again once the legs are unfolded.
If the machine wobbles, the length of one leg can
be adjusted by turning the end cap [1-7] until the
machine stands securely.
5.2 Prior to initial operation
5.2a Installing the guard (fig. 12)
- Remove the yellow safety sticker [12-4].
- Set the saw to maximum cutting depth and the
mitre to 0°.
- Pull the riving knife [12-1] into the upper posi-
tion.
- 1 Take hold of the guard [12-3] and com-
pletely unscrew the screw [12-2].
- 2 Place the guard [12-3] on the riving
knife [12-1]. In doing this, guide the lengthwise
pin that is located in the guard [12-3] into the
groove [12-6] on the riving knife [12-1] and push
the screw [12-2] into the hole [12-5] in the riving
knife [12-1] and tighten it.
- 3 Tighten the screw [12-2].
5.2b Installing the preset profile setting rail
Push the handle of the preset profile setting
rail into the zero position (fig. 15). Tighten the
screw [3-6] (fig. 3) and attach it to the table.
5.3 Transport
When transporting the power tool, hold
it by the handle areas on the sides [2-6].
Never take hold of or transport the power
tool by the protective cover.
- Click the saw unit into place in the zero position.
- Remove all attachments from your saw and wind
up the cable on the cable holder.
- Fold up the legs if necessary.
5.3a For transport over short distances, two of
the machine's leg ends are equipped with trans-
port rollers. Take hold of the power tool by the
handle area [2-6] and pull it to the desired place.
5.4 Scope of application
The machine can be used as a table saw or as a
table saw with sliding function.
a) Table saw (fig. 1)
- Set the switch [1-9] to the lower position.
- Swivel the handle [1-8] downwards and use it
to pull the saw unit forwards until it clicks into
place.
The saw unit is now in a central position on the
table and the machine can be used as a table saw.
b) Table saw with sliding function (fig. 3)
- Set the switch [3-10] to the upper position.
When the handle [3-9] is swivelled downwards, it
can move the saw unit backwards and forwards for
making cuts. The backwards motion is supported
by a spring force.
5.5 Dust extraction
The PRECISIO has two vacuum connec-
tions: A top guard with bayonet cou-
pling [2-3] with a diameter of 27 mm and
a bottom guard [2-2] with a diameter of
35 mm.
The CS 70 AB dust extraction set (included in the
delivery of CS 50 EB) connects the two vacuum
connections together so that a Festool mobile
dust extractor can be connected.
5.6 Power supply and operation
The mains voltage must correspond to
the specification on the rating plate.
- In North America, only Festool machines with
the voltage specifications 120 V/60 Hz may be
used.
- We recommend using a 16 A fuse because of the
performance of the motor.
- Before use always inspect the flexible lead and
the plug. Have the defects repaired by a special-
ist repair shop.
- Outside the premise use only approved exten-
sion leads and cable connections.
To switch the power tool on, press the ON/OFF
switch [4-1] and the locking switch [4-4] at the
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PRECISIO CS 50 EG - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PRECISIO CS 50 EG - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 7.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info