574995

Festool PALLAS50 Manual

13
Zoom out
Zoom in
Previous page
1/59
Next page
7.5
Adjusting
the
ruler
Open the screws
(15.1,
15.2) to adjust the two rulers
(Order No.
489679,
available from 08/99)
so
that
the
O-point
on
the scales
is
exactiy
in
li
ne
with the
cutting line
(15.3).
8 Use
as
a
trim
saw
(cross
cuts)
The drawgear
is
released by a slight pressure from
above on
the
handle (4.1). The saw can now be pul-
led forwards with one hand whilst the workpiece is
lifted with the other hand. Always place the work-
piece against a stop (see Chapter
10)
If
used
as
a
trim saw the protective cover must always be fitted
so
that the saw blade
is
always covered. The protec-
tive cover should hereby
be
lowered onto the work-
piece.
Concealed cuts, e.g. notches or grooves (Fig.
16)
are exceptions which are carried out without the pro-
tective
cover.
For the portable circular saw's original
riving knife
in
place of the protective cover for con-
cealed cuts. The protective cover must be replaced
immediatelyon completion of such work.
9 Use as a
bench
saw
(longitudinal
cuts)
Lock connecting
rod
in rear position. The saw is now
in
position for use as a bench (Fig. 17). The work-
piece must
be
guided along a longitudinal stop (see
section
10.3) during longitudinal cuts.
10
Limit
stop
system
A correctly set limit stop is
an
important precondition
for safe working with the saw. The versatile "Basis
WRA
500" mitre fence can be used as a transverse
stop, longitudinal stop or stop for
bevelled cuts. War-
ning: make sure that
all rotary knobs on the mire
fence are tight before starting work.
The "Basis WRA
500" mire lence can be mounted
on
all
lour
sides of the saw table
as
shown in illustra-
tion
18.
It
is ciamped in
pi
ace with the two rotary
knobs
(18.2).
The complete angle unit can
be
moved
in
a cros-
swise direction after releasing the rotary knob
(18.1).
10.1
Moving
the
mitre
fence
After the rotary knob (19.3) has been released the
mitre fence
(19.4) can be shifted along the angle unit
and optionally ciamped with a higher (Fig.
19) or
lower guide surlace (Fig.
17). Adjust the mitre fence
for cross and longitudinal cuts so that the max. gap
to the saw blade is
10 mm.
10,2
Angular
adjustment
for bevelied
cuts
After releasing the rotary knob (19.2) and pulling out
the locking pin
(19.1) any angle can be set between
-90°
and +90°. The locking pin can be notched
in
place for common angle settings.
10.3
Longitudinal
stop
Fitthe mire fence
as
shown
in
Fig. 17 for longitudinal
cuts. Alternatively, the "Basis
LA
650" longitudinal
stop
(20.1, Order No.
489675),
available as
an
extra, can also
be
used. Make sure that the gap bet-
ween the stop rai! and saw blade does not diminish
towards the back. Otherwise there is a risk that that
cut. -oft parts of the workpiece may become jammed
between the saw blade and stop rai!.
Set the stop
rail
to
the lower setting and use
the
enclosed guide handle (17.1) when sawing workpie·
ces narrower than 120 mm.
11
Chan
ging
the
saw
blade
Always wear safety gloves when chan ging saw bla·
des (risk
of
injury
on
teeth) Remove the portable
saw circular
to
change the saw blade (see section
5). The further steps are described
in
the operating
instructions for the portable circular saw
..
12
Connection
of
a
dust
extractor
The optional dust extractor set (Order No.
488292)
allows you
to
connect the "Basis 1
A",
"Palias 50"
Basis·Set
to
a Festool dust extractor. The dust
extractor set permits the simultaneous extraction
01
dusts and chips from the portable circular saw
(0
36
mm) and upper protective cover
(0
27
mm).
13
Maintenance and
service
Warning: Always disconnect the mains plug
from
the
socket before carrying out any maintenance work.
Keep the ventilation slots in the motor housing clean
and free of obstructions at
all times to ensure
an
adequate circulation of
air.
The device
is
fitted with special motor brushes with
an
automatie cut-out. When the brushes become
worn the power supply is shut oft automatically and
the tool comes to astandstill.
Any maintenance and repair work requiring
en
ope-
ning
of
the motor housing may only be carried out
by
an
authorised custorner service workshop.
14
Accessorles
Festool ofters a wide range
01
accessories for
the
"Basis
1A:',
"Pallas 50" Basis-Set,
e.
g. trimming
attaehment, sliding table, extension table, dust
extractor set, ete
..
More details can be lound
in
the
Festool catalogue.
15 Warranty
Our equipment
is
under warranty for at least
12
months with regard to material or production faults
in
aceordance with national legislation.
In
the
EU
countries, the warranty period is 24 months
(an
involce or delivery note
is
required as proof of pur·
chase).
Damage resulting from,
In
partieular, normal wear
and tear, overloading, irnproper handling, or eaused
by the user or other damage caused
by
not lollowing
the operating Instruetlons, or any lault acknowled-
ged at the time
01
purchase, Is not covered
by
the
warranty.
Complalnts
will only be acknowledged if the equip-
ment has not been dlsmantled before being sent
back to the suppliers or to an authorised Festool
customer support workshop. Store the operating
Instructlons, safety notes, spare parts list and proof
01
purchase
In
a sale place.
In
addition, the manu-
facturer's current warranty condltlons apply.
Note
We
reserve the rlght to make changes to the technl-
cal data eontalned
In
thls information
as
a result of
ongolng research and development work.
13
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PALLAS50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PALLAS50 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info