778808
19
Zoom out
Zoom in
Previous page
1/110
Next page
LHS-E 225
19
GB
Extraction power is insuf-
ficient.
Filter element on the CTL/M 36 E
AC
PLANEX
is blocked/
clogged.
Clean the filter element regularly:
Option 1:
Set the suction power adjust-
ment to maximum. Using the surface of
your hand, keep the nozzle, suction hose
or suction opening on the mobile dust
extractor covered for 10 seconds until
automatic cleaning begins.
Option 2:
Manually clean the filter ele-
ment (dust extraction).
Option 3:
Check the filter element for
damage and clogging. Use a new filter
element regularly.
Disposal bag inserted incorrectly. The holes punched in the disposal bag
must be inside the container.
Filter bag inserted instead of dis-
posal bag.
Always work with the disposal bag when
operating the PLANEX (grey bag).
The suction power on the CTL/M
36 E AC
PLANEX
is set too
low.
Adjust the suction power to a higher set-
ting.
LHS-E 225 speed too high Reduce speed.
Suction hose blocked or kinked. Remove blockage and straighten hose.
Disposal bag full Dispose of the bag.
Brush segment open/not fitted. Only remove the brush segment when
sanding close to edges, refit it, see Sec-
tion 7.4.
The holes in the sanding discs are
not aligned with the holes in the
sanding pads.
Fit the sanding discs correctly, see Sec-
tion 7.3.
Excessive material
removed from workpiece
LHS -E 225 speed too high Reduce the speed, see Section 7.1
Grit on abrasive too coarse Select a finer grit.
Surface quality not per-
fect
Incorrect abrasive grit Select a finer grit.
Drying times of the spackling
paste not observed.
Read the technical data sheets and manu-
facturer's recommendations.
Spackling paste with a high per-
centage of filler/soft filler
Select a finer grit, e.g. P180.
Power tool running when set
down on the surface (groove for-
mation).
Place the power tool in position and then
switch it on.
Always use a detachable brush segment
when working on the surface.
Sanding marks on the
surface
Sanding pad is placed down on
the surface at an angle
Place the sanding pad down so that it is
level.
The abrasive grit is too coarse for
very soft spackling paste.
Choose a finer abrasive grit (abrasive
Brilliant 2 available up to grit P 320).
LHS-E 225 switches off
while working and after
three beeps
Cool air filter on the LHS-E 225 is
blocked.
Clean the cool air filter on the LHS-E 225,
see Section. 9.1.
Excessive pressure -> power tool
activates overheating protection.
Let the power tool cool down for approx.
15 minutes and then apply less pressure.
Problem Possible causes Remedy
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool LHS-E 225 EQ Planex Easy at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool LHS-E 225 EQ Planex Easy in the language / languages: All languages as an attachment in your email.

The manual is 12.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info