573119

Festool HK132E Manual

20
Zoom out
Zoom in
Previous page
1/114
Next page
20
switches the motor off before the motor is able to
reach a critical temperature. After a cooling period
of approx. 3–5 minutes the machine is once again
ready for operation and can run at full load. The
cooling period can be greatly reduced if the ma-
chine is running (idling or recovery speed).
7.2 Cutting Depth Adjustment
Release the locking lever [1-16].
Set the required depth on the cutting depth scale
[1-15].
Raise: smaller cutting depth
Lower: larger cutting depth
Re-tighten the clamping lever [1-16]
.
To achieve the best cutting results, the saw blade
should protrude from the material by no more than
3 mm.
7.3 Cutting Angle Adjustment
Release the cutting angle locking lever at [1-7] and
[1-18].
Set the cutting angle as required using the scale
[1-19]. (The scale is calibrated in 1° increments).
Re-tighten the cutting angle locking lever at [1-7]
and [1-18].
WARNING
The maximum cutting depth is reduced for
bevel cuts.
7.4 Cut indicator
The cut produced by the HK 132 E depends on the
bevel setting and can be observed at the cut indica-
tor.
7.5 Parallel Guide
Various parallel guides can be inserted into the ma-
chine base plate [2-2] on the left [2-3] and on the
right [2-4].
Tighten the parallel guide using the winged screws
[2-1].
7.6
Dust extraction
CAUTION
Inhaled dust may damage the air pas sages.
Tools should be permanently connected to
the dust extracting plant.
Wear respirator if you work with dust.
.
To extract dust, suction adapter [1-1] can be mount-
ed on the sawdust ejector through which common
extract hoses of dust extractors can be connected.
7.7 Replacing the Saw Blade
WARNING
Risk of injury
Before exchanging the saw blade, pull the
mains plug from the power sup ply socket.
Wear protective gloves!
The sawing performance and the quality of the
cut depend essentially on the condition and tooth
form of the saw blade. Therefore, use only sharp
saw blades that are suitable for the material to be
worked.
Swing back the swinging guard with the lever [3-5].
Install a suitable saw blade according to the illus-
tration and tighten. Take care that the mounting
flange [3-4] and the clamping flange [3-2] are cor-
rectly positioned. The holes in the saw blade [3-3]
must fi t onto the follow-up pins on the mounting
fl ange [3-4].
WARNING
Risk of injury
Observe for installation: The cutting direction
of the teeth (arrow on the saw blade) must
match the direction of the arrow on the guard.
Check the function of the swinging guard.
Tighten the hexagon bolt [3-1] using the SW19 Allen
key supplied, while holding the clamping fl ange
[3-2] with the single ring spanner which is also sup-
plied.
To remove the blade, follow the same sequence in
reverse.
8 Operating Instructions
- Do not cut into nails, screws, etc.
- Do not work with materials containing asbestos.
- Do not use saw blades that have cracks or that
are damaged.
- Under no circumstances use abrasive disks!
- Saw blades of highly alloyed, high-speed steel
(HSS-steel) must not be used.
- Feeding too fast signifi cantly reduces the per-
formance of the machine and short ens the life
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool HK132E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool HK132E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info