778534
26
Zoom out
Zoom in
Previous page
1/164
Next page
equipped with an AVR (automatic voltage
regulator); the power tool will not operate
correctly without this regulator and may be
damaged.
The power output of the EG must be at
least 2.5 times greater than the connected
load of the power tool (i.e. 6 kW).
If the power tool is operated using an EG
that is not sufficiently powerful, the speed
may fluctuate and the power output of the
power tool may drop.
9 Service and maintenance
WARNING
Risk of injury, electric shock
Always pull the mains plug from the socket
before performing any servicing and main
tenance work.
All maintenance and repair work which re
quires the motor housing to be opened
should always be carried out by an author
ised service workshop.
Customer service and repairs must
only be carried out by the manufac
turer or service workshops. Find the
nearest address at:
www.festool.co.uk/service
Always use original Festool spare
parts. Order no. at:
www.festool.co.uk/service
EKAT
1
235
4
Cleaning the machine regularly, espe
cially the adjusting devices and guides, is
an important safety factor.
Observe the following instructions:
Damaged safety devices and parts, such as
a faulty lever for changing tools [1-3], must
be properly repaired or replaced in a recog
nised specialist workshop, unless otherwise
indicated in the operating manual.
To ensure constant air circulation, always
keep the cooling air openings in the housing
clean and free of blockages.
Use an extractor on all openings in order to
remove wood chips and splinters from the
power tool. Never open the protective
lid [1-7].
The pendulum guard must always be able to
move freely and close independently. Al
ways keep the area around the pendulum
guard clean. Clear from dust and chippings
by blowing out with compressed air or using
a brush.
When working with plaster- and cement-
bonded fibreboards, clean the tool particu
larly thoroughly. Clean the vents of the
power tool and on/off switch using dry, oil-
free compressed air. Otherwise, gypsum
dust deposits may build up inside the power
tool's housing and on the on/off switch and
harden when exposed to humidity. This may
impair the switching mechanism
10 accessories
The PO numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet at "www.festool.com".
In addition to the accessories described,
Festool also provides a comprehensive range of
system accessories that allow you to use your
saw more effectively and in diverse applica
tions, e.g.:
set-back stop FS-RSP
SB-TSC chip collection bag
PA-A HK elbowed parallel side fence, gui
ded on both sides
Groove unit VN-HK85 130x16-25
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli
cations and these are specially designed for
your Festool saw.
10.2 Parallel side fence [8]
The parallel side fence (on both sides) is de
signed to guide the saw parallel to the edge of
the workpiece [8A] and can also be used as an
extension table [8B] to achieve a straight, pre
cise cut.
10.3 Guide rail
The guide rail enables you to make clean, accu
rate cuts while simultaneously protecting the
surface of the workpiece from damage.
In conjunction with the extensive range of ac
cessories, exact angled cuts, mitre cuts and fit
ting work can be completed with the guide sys
tem. The option of attaching the guide rail se
curely using clamps [7-6] ensures safer work
ing conditions.
Adjust the guide play between the saw table
and the guide rail using the two adjustable
jaws [7-8].
English
26
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool HK 85 EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool HK 85 EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7.99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info