778634
17
Zoom out
Zoom in
Previous page
1/88
Next page
DTSC 400 Li, RTSC 400 Li
17
GB
Loosen both ends of the edge protector.
Remove the edge protector by pulling it for-
wards.
8 Working with the machine
Observe the following instructions:
Do not overload the machine by pressing with ex-
cessive force! The best sanding results are
achieved with moderate application pressure.
The sanding capacity and quality are mainly de-
pendent on the selection of the correct abrasive.
Work in corners and on edges tends to subject
the tip to increased stress and results in in-
creased heat development. In such cases, work
with reduced contact pressure.
Hold the machine with one hand on the handle
[1-8]
.
8.1 Warning signal
The machine shuts down and makes a sound:
Switch off the machine.
Battery pack is empty.
Change the battery pack.
The machine shuts down and does not make a
sound:
Machine is overheated or has been overloaded.
Switch off the machine for 30 seconds.
Reduce the machine load.
If the machine's final speed is then not reached, al-
low the machine to cool down.
9 Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at: www.festool.com/service
Only use original Festool spare parts!
Order No. at: www.festool.com/service
To ensure constant air circulation, always keep the
cooling air openings in the motor housing clean and
free of any obstruction.
In the event of a slowdown in performance or in-
creased vibrations, blow and clean cooling air
openings.
Keep the contacts on the machine, charger and
battery pack clean.
For service, maintenance, disposal and
transport of the battery pack, note enclosed
instructions of the battery pack!
10 Accessories
Use only original Festool sanding pads. Low-quality
sanding pads may cause serious machine imbal-
ance that decreases the quality of the working re-
sults and increases machine wear.
The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
11 Environment
Do not dispose of electric power tools in house-
hold waste!
Recycle devices, accessories and
packaging. Observe applicable country-specific
regulations.
EU only:
In accordance with European Directive on
waste electrical and electronic equipment and im-
plementation in national law, used electric power
tools must be collected separately and handed in
for environmentally friendly recycling.
Information on REACh:
www.festool.com/reach
Information on data protection
The power tool contains a chip which automatically
stores machine and operating data (RFID). This
data saved cannot be traced back directly to an in-
dividual.
WARNING
Risk of injury
Always secure the workpiece in such a manner
that it cannot move while being machined.
WARNING
Risk of injury, electric shock
When carrying out servicing and maintenance
work, always remove the batteries or the mains
adapter from the power tool first.
All maintenance and repair work which requires
the motor housing to be opened should always
be carried out by an authorised service work-
shop.
EKAT
1
235
4
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool DTSC 400 Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool DTSC 400 Li in the language / languages: All languages as an attachment in your email.

The manual is 22.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info