Manual Festool DSC-AG 125 (page 18 of 126) (All languages)

778812

Zoom out

Zoom in

1/126

designed may create a hazard and cause per-

sonal injury.

c) Do not use accessories which are not speciﬁ -

cally designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not as-

sure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked

on the power tool. Accessories running faster

than their rated speed can break and ﬂ y apart.

e) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded or

controlled.

f) The arbour size of wheels, ﬂ anges, backing

pads or any other accessory must properly ﬁ t

the spindle of the power tool. Accessories with

arbour holes that do not match the mounting

hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss

of control.

g) Do not use a damaged accessory. Before each

use inspect the accessory such as ABRASIV

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or ac-

cessory is dropped, inspect for damage or

install an undamaged accessory. After in-

specting and installing an accessory, posi-

tion yourself and bystanders away from the

plane of the rotating accessory and run the

power tool at maximum no-load speed for one

minute. Damaged accessories will normally

break apart during this test time.

h) Wear personal protective equipment. Depend-

ing on application, use face shield, safety gog-

gles or safety glasses. As appropriate, wear

dust mask, hearing protectors, gloves and

workshop apron capable of stopping small

ABRASIV or workpiece fragments. The eye

protection must be capable of stopping ﬂ ying

debris generated by various operations. The

dust mask or respirator must be capable of

ﬁ ltrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken acces-

sory may ﬂ y away and cause injury beyond im-

mediate area of operation.

j) Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring

or its own cord. Cutting accessory contacting a

“live” wire may make exposed metal parts of

the power tool “live” and shock the operator.

k) Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled

into the spinning accessory.

l) Never lay the power tool down until the acces-

sory has come to a complete stop. The spin-

ning accessory may grab the surface and pull

the power tool out of your control.

) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the hous-

ing and excessive accumulation of powdered

metal may cause electrical hazards.

o) Do not operate the power tool near ﬂ ammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Further safety instructions for all operations

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging causes

rapid stalling of the rotating accessory which in

turn causes the uncontrolled power tool to be

forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an ABRASIV wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point of

pinching. ABRASIV wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/

or incorrect operating procedures or conditions

and can be avoided by taking proper precautions

as given below.

a) Maintain a ﬁ rm grip on the power tool and

position your body and arm to allow you to

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool DSC-AG 125 in the language / languages: All languages as an attachment in your email.

The manual is 7.06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool DSC-AG 125 Manual

Product: