510172
16
Zoom out
Zoom in
Previous page
1/100
Next page
16
DF 700 EQ
GB
9 Service and maintenance
The machine is equipped with special carbon
brushes. If they are worn, the power is interrupted
automatically and the machine comes to a stand-
still.
Observe the following instructions:
To ensure constant air circulation, always keep
the cooling air openings in the housing clean
and free of blockages.
Clean the guides
[3-1]
and
[3-6]
of dust depos-
its.
Oil the guides regularly and lightly with resin-
free oil (e.g. sewing machine oil).
We recommend an annual inspection and/or a
check after approx. 100 operating hours at an
authorised customer service workshop. This is
for the safety of the user and the value stability
of the power tool.
10 Troubleshooting
See chapter
1. Select a DOMINO dowel and insert the
suitable bit into the DOMINO joining
machine.
7.2
2. Set the routing depth. 7.3
3. Set the routing height. 7.4
4. Adjust the routing angle if necessary. 7.5
5. Mark the areas on the workpieces that
belong together
[8-1]
so that you will be
able to join them correctly again once
you have cut the dowel holes.
6. APosition the two workpieces to be joined
against one another and mark the
desired positions of the DOMINO dowels
with a pencil
[8-2]
.
6.
B
Select the required stop pins. 7.7
7. Set the desired dowel hole width (ade-
quate fit or with 3 mm play).
7.6
8. Cutting the dowel holes
[8]
:
The first dowel hole by attaching the
stop pin to the side edge of the work-
piece.
The following dowel holes according
to the previously made pencil mark-
ings and the scale of the vision panel
[8-3]
.
Our recommendation:
Please check
each dowel hole for chippings and clear
these if necessary.
Always work with a dust extractor to
improve the removal of chippings.
Route the first hole for each workpiece
without play (dowel hole width = DOM-
INO dowel width) and the other dowel
holes with the large dowel hole width.
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing maintenance work on
the machine!
All maintenance and repair work which requires
the motor housing to be opened must only be
carried out by an authorised service workshop.
See chapter
Fault Cause Solution
Burns Blunt cutter Use sharp cutter
Dowel hole too narrow. DOMINO
dowel cannot be jointed.
a. Blunt cutter
b. Deposits (e.g. chippings in the
dowel hole)
a. Use sharp cutter
b. Remove deposit and work with
dust extractor
Widening of the dowel hole with
8mm cutter
Routing depth too large (larger
than 50 mm)
Reduce routing depth (max.50 mm)
Splinters at edge of dowel hole Excessive feed rate Reduce feed rate
Dowel hole not parallel to work-
piece edge
Workpiece has shifted during
processing
Secure workpiece properly
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool DF 700 EQ-Plus Domino XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool DF 700 EQ-Plus Domino XL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info