510172

Festool DF 700 EQ-Plus Domino XL Manual

14
Zoom out
Zoom in
Previous page
1/100
Next page
14
DF 700 EQ
GB
when under load.
Temperature cut-out
The machine power supply is limited and the speed
reduced if the motor exceeds a certain tempera-
ture. The machine continues operating at reduced
power to allow the ventilator to cool the motor
quickly. If the machine temperature exceeds the
maximum permitted value for longer periods, the
machine switches off completely after approx. 40
seconds and can only be switched on again once the
motor has cooled sufficiently.
Restart protection
The integral restart protection prevents the ma-
chine from automatically starting up again after an
interruption in power when the machine is used in
continuous operating mode. In this case the ma-
chine must be switched off and then switched back
on again.
7.2 Changing tools
Removing the tool
Lift the unlocking device
[3-2]
until it audibly
disengages using the open-ended spanner
[3-
3]
supplied (SW 12).
Separate the motor unit
[3-5]
from the guide
frame
[3-4]
.
Press and hold the spindle lock
[4-1]
.
Loosen the cutter
[4-3]
using the open-ended
spanner
[4-2]
and remove.
Release the spindle lock
[4-1]
.
Inserting the tool
Press and hold the spindle lock
[4-1]
.
Use the open-ended spanner
[4-2]
to screw on
the cutter
[4-3]
.
Release the spindle lock
[4-1]
.
Slide the guide frame
[3-4]
onto the motor unit
[3-5]
until it audibly engages.
7.3 Setting the Mortise Depth
Press one or two snap buttons
[1-8]
.
Set the slide for the routing depth setting
[1-
7]
to the desired routing depth (15 - 70 mm).
Release the snap buttons
[1-8]
.
Check whether the slide
[1-7]
has engaged cor-
rectly.
With the two markers
[1-9]
, you can mark two
routing depths and switch easily between them
using the slide
[1-7]
(e.g. for asymmetric DOMI-
NO dowel depth distribution).
7.4 Setting the Fence Height
The alignment of the clamp levers
[1-12]
and
[1-14]
can be aligned by raising the levers.
When tightened, the levers should not protrude
beyond the contact surface.
a) with selection slide
Loosen the clamp lever for the routing height
adjustment
[5-1]
.
Using the front handle
[5-2]
raise the front part
of the guide frame.
Use the selection switch to set
[5-6]
the desired
routing height
h
(10 mm; 15 mm; 20 mm;
25 mm; 30 mm; 40 mm).
Press the front section of the guide frame down-
wards as far as the stop.
Close the clamp lever
[5-1]
.
b) freely selectable
Loosen the clamp lever for the routing height
adjustment
[5-1]
.
Using the front handle
[5-2]
raise the front sec-
tion of the guide frame.
Pull the selection slide
[5-6]
as far as the stop
in the direction of the motor unit.
Set the desired routing height
h
using the scale
[5-3]
by moving the front section of the guide
frame vertically.
Close the clamp lever
[5-1]
.
CAUTION
Hot and sharp tools
Risk of injury
Wear protective gloves.
WARNING
Risk of injury
Before inserting a new cutter ensure that the
machine, the guide frame and the guides
[3-1]
and
[3-6]
are clean.
Remove any contamination that may be present.
Only use sharp, undamaged and clean tools.
WARNING
Cutter can come out at the rear side of the work-
piece.
Risk of injury
Set the routing depth at least 5 mm less than the
workpiece thickness.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool DF 700 EQ-Plus Domino XL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool DF 700 EQ-Plus Domino XL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info