499144
11
Zoom out
Zoom in
Previous page
1/54
Next page
11
solids (e.g. acid, leach, solvent).
- Observe all national safety regulations as well
as the material manufacturer‘s specifi cations!
- Always use suitable protective equipment!
- If intact following a visual inspection, work in a
dry environment according to instructions!
- Always use the socket on the machine for the
purpose specifi ed!
- Do not lift or transport using a crane hook or
lifting gear!
- Do not pull plug out of mains socket by its cable.
- Protect cable against heat, oil and sharp edges.
- Check plugs and cables regularly and have them
replaced by an expert if damaged.
3 Operation
WARNING
Unauthorised voltage or frequency!
Risk of accidents
f Observe the specifi cations on the machine’s
name plate.
f Observe country-specifi c regulations.
3.1 Connecting the mobile dust extractor
WARNING
Risk of injury from tools starting up unexpect-
edly
f Before setting the switch to the „AUTO“ or
„MAN“ position, make sure that the con-
nected tool is switched off.
f Insert the plug into an earthed socket.
Pull the plug from the socket when the
machine is not in use and prior to main-
tenance and cleaning work.
The switch [1-1] serves as an on/off switch.
Switch position “0”
Appliance socket [1-3] is disconnected from the
power, mobile dust extractor is switched off.
“MAN” switch position
Appliance socket [1-3] is connected to the power,
the mobile dust extractor starts.
Auto” switch position
Appliance socket [1-3] is connected to the power,
the mobile dust extractor starts when the con-
nected tool is switched on.
3.2 Connecting electric power tools
WARNING
Risk of injury
f Observe the maximum appliance socket con-
nected load (see chapter „Technical data“)
f Switch off the electric power tool.
f Connect the electric power tool to the appliance
socket [1-3].
3.3 Connecting the suction hose
The extractor hose [4-2] is connected to the ex-
tractor opening by the angle bracket [4-1].
A Systainer can be attached to the storage area
[5-6] via the four locking clips [5-5].
3.4 Adjusting the suction power
f Use the rotary knob [1-2].
3.5 Temperature cut-out
A temperature cut-out switches the mobile dust
extractor off when it reaches a critical tempera-
ture to prevent overheating.
f Switch off the mobile dust extractor, allow to
cool for about 5 minutes then switch on again.
f Not possible to switch on: contact Festool ser-
vice workshop.
3.6 Stand/Brake
Folding out the stand [4-4] prevents the mobile
dust extractor from rolling away. Lift the front end
of the mobile dust extractor slightly and push the
stand downwards until it latches into place. Press
the button [4-3] to release.
4 Working
4.1 Extracting dry materials
CAUTION
Hazardous dust
Damage to the respiratory passage
f Always use a fi lter bag!
When extracting large quantities of oak
or beech wood dust or dust that exceeds
the permitted limit values, only extract from a
single machine.
Observe the following when extracting dust gener-
ated by operating electric power tools:
Ensure there is adequate ventilation! Observe
regional regulations!
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CTL Mini at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CTL Mini in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info