Manual Festool CS70E-S PR (page 18 of 110) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

573130

Zoom out

Zoom in

1/110

Lay the insert in position and secure with the

clamp and the rotary knob [5-1].

7.6 Setting the spacer wedge

Once the protective cover is removed, pull ﬁ rmly

on the spacer wedge [1-6] to move to one of two

catch positions. The spacer wedge is used in the

top catch position [7-2] in the all applications,

except concealed cuts.

For concealed cuts only

Remove the top protective cover.

Press down the spacer wedge ﬁ rmly to move

to the lower catch position [7-1].

When producing concealed cuts, make sure you

guide the machine accurately. Press the work-

piece ﬁ rmly onto the table. When cutting the

workpiece, make sure that the side of the work-

piece that is already cut out is not on the same

side as the fence.

After completing concealed cuts, move the

spacer wedge [1-6] back to the top position

and attach the protective cover (see chapter

6.1).

7.7 Fence

The fence can be attached at any point along

the clamping edge of the saw base and is

so versatile, it can be used as a cross stop

[Fig. 1] or a longitudinal stop [Fig. 6].

 Before attaching, make sure that the contact

surfaces of the fence are not dirty.

WARNING

Risk of injury

Always use the fence in a ﬁ xed position and

do not use to slide the workpiece along!

Fitting the fence

Open the clamping jaws using the knob [4-4].

Place the fence with guide rail [4-5] onto the

clamp rail from above.

Secure the clamp segment using the knob [4-

4].

The fence can be adjusted in the following ways:

Move the fence on the clamp segment

Unscrew the rotary knob [1-5] and move the

fence.

Move the stop ruler

Unscrew the rotary knob [4-1] and move the

fence.

 The stop ruler is stepped on one side by

8 mm. This guide rail can be used to guide

the cross stop up to the saw cut to support

the workpiece without having to remove the

top protective cover.

Adjust the angle

Unscrew the rotary knob [4-2] and lift the re-

taining pin [4-3].

The rotary retaining pin engages at the most fre-

quently used angle settings.

Adjust the position of the stop proﬁ le

Unscrew the rotary knob [4-1].

Remove the guide rail [4-6] and turn 90°.

Place the guide rail in the guide slot available.

[Fig. 4]

The dimensions of the aluminium proﬁ le provide

a high guide surface for high workpieces and a

low guide surface for ﬂ at workpieces.

Longitudinal stop

Position the stop ruler parallel to the blade to

make rip cuts.

Use the workpiece holder [6-1] for guiding

narrow workpieces.

The two rulers on the left and right of the saw

blade cutting edges [7-1] are set to zero ex works

so that the fence can be aligned with the scale

along the front edge of the table.

7.8 Fitting the splinterguard

NOTE

The splinterguard cannot be used when making

bevel cuts. Remove the splinterguard as neces-

sary.

Unscrew the rotary knob [5-1].

Slide the clamping plate forwards.

Lift the table insert [1-4] from the rear end and

remove.

Set the saw blade to the minimum cutting

depth.

Slide the splinterguard [8-3] up to the side of

the retainer [8-1].

Place the table insert [1-4] in position and

tighten the rotary knob [5-1].

Switch on the machine and move the saw blade

slowly upwards to the maximum cutting depth.

This beds in the splinterguard. The raised sec-

tion [8-4] of the splinterguard should protrude

slightly (approx. 0.3 mm) over the edge of the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool CS70E-S PR in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool CS70E-S PR Manual

Product: