Manual Festool bs 75 e (page 9 of 62) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

390048

Zoom out

Zoom in

1/62

BS 75/BS 75 E

Sound pressure level 92/91 dB (A)

Sound power level 103/102 dB (A)

Measuring uncertainty allowance K = 3 dB

Wear ear protection!

Overall vibration levels a

(vector sum for three

directions) measured in accordance with EN

60745:

Handle a

< 2.5 m/s²

K = 1.5 m/s²

Front handle a

= 7.5 m/s²

K = 2.0 m/s²

The emission values speciﬁ ed (vibration, noise)

were measured in accordance with the test con-

ditions stipulated in EN 60745 and are intended

for machine comparisons. They are also used for

making preliminary estimates regarding vibration

and noise loads during operation.

The emission values speciﬁ ed refer to the main

applications for which the power tool is used. If

the electric power tool is used for other applica-

tions, with other tools or is not maintained suf-

ﬁ ciently prior to operation, however, the vibration

and noise load may be higher when the tool is

used. Take into account any machine idling times

and downtimes to estimate these values more

accurately for a speciﬁ ed time period. This may

signiﬁ cantly reduce the load during the machine

operating period.

2 Mains supply

The mains voltage must match the voltage on

the rating plate.

Fuse for 230 V: 10 Amp slow action or equivalent

automatic cut-out.

Connection is also possible to sockets without an

earthing contact, as protective insulation (Class

II) is present.

Only use a run out extension lead with a cross

section of 3 x 1.5 mm

, max. 20 m, (3 x 2.5 mm

max. 50 m). When tool is used outdoors, use only

extension cords intended for use outdoors and

so marked.

3 Electronic adaptation of belt speed on

types BS 75 E

The control electronics permits the in-

ﬁ nitely variable adaptation of the belt

speed.

Setting of set wheel Belt speed

(no-load)

1 200 m/min

2 240 m/min

3 300 m/min

4 340 m/min

5 360 m/min

6 380 m/min

The most suitable belt speed must be found

by trial and error when starting work, because

there are several prime factors which inﬂ uence

the choice, such as the surface and quality of the

workpiece, the make of abrasive belt and grit, skill

of the operator etc.

The ﬁ gures shown in the table are only recom-

mended values.

Application Setting of set

wheel

Grit

Solid wood,

ﬁ ne

4 - 6 100

Veneer 3 - 4 120

Chipboard 5 - 6 100

Plastics 1 - 4 100

Steel 2 - 4 80

Paint remova 1 - 3 24

The belt speed is inﬁ nitely adjustable up to the

maximum setting while work is in process.

This is done by turning the set wheel (2.1).

It must be remembered that at low speed settings

the sander has a lower power output. In order to

avoid overloading, therefore, the speed has to be

increased by turning the set wheel if it turns out

that the belt speed falls sharply while working.

4 Operation

Only to be switched on when the machine is

raised. Using the lock on button (1.2), the switch

(1.3) can be locked in the ON position. Before

sanding, check the alignment of the belt and if

necessary, adjust by turning the adjusting knob

(1.4) until the belt is ﬂ ush with the outside edge

of the sanding face.

Using both hands, place the machine straight onto

the workpiece to be sanded.

The actual weight of the machine provides ad-

equate sanding pressure to produce good sanding

quality.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool bs 75 e in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool bs 75 e Manual

Product: