724612
24
Zoom out
Zoom in
Previous page
1/42
Next page
47.1cc Petrol Chainsaw
AFTER SALES SUPPORT
1300 889 028
(toll free)
e-mail: info.aldi@positecgroup.com
MODEL: №. 10084 • 08/2019 • FCS4800A
22
Checking the operation of the clutch.
Each time the chainsaw is started, the operation of the clutch (22) should
be checked as per the following detail. The chain MUST rst be checked to
ensure correct tension adjustment before starting.
1. When attempting to start the chainsaw, the chain (20) should not be trying
to move around the guide bar (19) under the inuence of the recoil starter
(11). If it is trying to rotate around the guide bar (19), STOP the starting
process and take the saw to an authorised service centre.
2. If point 1 is correct and the chain (20) is not trying to rotate around the
guide bar (19), start the chainsaw as per the section in the manual “Starting
the Chainsaw”.
3. With the chainsaw operating and at idle and ensuring the chain (20) is in
a safe position with respect of other persons and any objects, release the
chain brake (13).
CHECK, the chain (20) should NOT be rotating around the guide bar (19) at
idle speed.
4. Operate the safety lever (2) and then accelerate the throttle trigger (3).
The chain (20) should start and rotate. The harder the throttle trigger (3)
is pulled, the faster the chain (20) will rotate. RELEASE the throttle trigger
(3) so the motor returns to the idle condition. The chain (20) MUST stop
rotating around the guide bar (19) when the motor of the saw is at idle.
5. If the chain (20) is constantly rotating when the motor of the saw is at idle,
the chainsaw should NOT be used and the chainsaw should be taken to an
authorised service centre for repair.
6. DO NOT use the chainsaw if the clutch (22) does not totally disengage
when the motor of the saw is at idle.
Re-setting the Chain Brake
The front guard / chain brake (13) operates automatically in the event of
kickback. In the event of a kickback, the guide bar (19) kicks up, the wrist of
the operator’s hand on the top handle knocks against the front guard / chain
brake (13) causing it to move forward thus activating the chain brake (13).
To reset the front guard / chain brake (13) this can be done manually by
pulling it rmly towards the back of the chainsaw until a click is heard. (Fig A).
CAUTION: Each time the chainsaw is used, check that the chain brake (13)
is operating correctly.
Operation
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex FCS4800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FCS4800A in the language / languages: English as an attachment in your email.

The manual is 8,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info