779785
28
Zoom out
Zoom in
Previous page
1/44
Next page
28
front end.
12. Check that the table insert is secure: The
table insert must be  ush with the saw
table.
13. Secure the table insert using the two
fastening screws.
Fitting the parallel stop (Fig. 21)
1. Slide the stop rail (22) onto the parallel
stop (20) so that the square necks of the
two lock bolts slide into the pro le of
the stop rail.
2. Secure the stop rail on the parallel stop
by tightening the two knurled nuts.
3. Place the parallel stop with open ec-
centric lever (35) on the rail (36) on the
saw table.
4. To change to position of the parallel
stop, move the parallel stop with open
eccentric lever to the right or left.
5. Press the eccentric lever completely
down to secure the parallel stop in the
desired position.
Connecting a vacuum extraction device
(Fig. 22)
The dust extraction connector (37) is
located on the back of the bench-type
circular saw.
Connect the suction hose of a suitable
chip extraction system (e.g. a multi-
purpose vacuum cleaner) to the dust
extraction connector (37) and secure
it with, e.g. a hose clip. Please note: A
normal household vacuum cleaner is
not suitable to be used as a vacuum
extraction device in this case.
6. Operation
Setting the cutting depth
Use the crank (32) to turn the saw blade
(31) out of the saw table (1) and lower it
into the saw table. Adjust it to the depth you
require as follows:
Increasing the cutting depth:
Turn the crank clockwise so that the saw
blade is moved out of the saw table.
Reducing the cutting depth:
Turn the crank counterclockwise so that
the saw blade is lowered into the saw
table.
Setting the cutting angle (Fig. 23)
1. Turn the locking screw (38) approx. one
revolution counterclockwise to slacken
it.
2. Use the crank wheel (39) to adjust the
cutting angle to the angle you require
on the angle scale (40).
3. Turn the locking screw clockwise to
tighten it and secure the saw blade (31)
F_TS_2000_1_GB_SPK7.indb 28F_TS_2000_1_GB_SPK7.indb 28 04.06.2019 10:19:0104.06.2019 10:19:01
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex F-TS 2000-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex F-TS 2000-1 in the language / languages: English as an attachment in your email.

The manual is 3.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info