779785
26
Zoom out
Zoom in
Previous page
1/44
Next page
26
5. Before using the equipment
Before you connect the equipment to the
power supply make sure that the data on
the rating plate are identical to the supply
voltage.
Warning!
Always pull out the power plug before
making adjustments to the equipment.
Assembly
WARNING! Risk of injury!
If you assemble the bench-type circular
saw incorrectly, this could lead to serious
injuries.
Assemble the bench-type circular saw cor-
rectly and completely, including all covers
and safety devices, before using for the  rst
time.
Never under any circumstances insert
the power plug into the socket outlet
before completion of assembly.
Fitting the legs. (Fig. 5-11)
1. Turn the saw table (1) over and set it
down on the  oor.
2. Fit the four legs (8) loosely to the saw
table with the help of two hexagon
screws (25) and two large washers (28)
for each leg.
3. To do so, use the drill holes provided in
the saw table and the threaded sockets
in the legs.
4. Then  t one middle strut (9) between
each of the legs by inserting the faste-
ning opening at the ends of the middle
strut into the detents on the legs and
pressing them so that they lock into
place.
5. Secure the middle struts to the legs
using two lock bolts (23), two small
washers (27), two spring washers (24)
and two hex nuts (29) on each.
6. Now tighten all the screw connections.
7. Then plug one rubber foot (11) onto
each leg (8).
8. Then  t one tilt guard (10) to each of
the rear legs using two hexagon screws
(24), spring washers (26), small was-
hers (27) and hex nuts (29) each.
Fitting the table width extension
(Fig. 12)
1. To be able to  t the table width exten-
sion (7), remove the screw (A) on both
undersides of the guide tubes.
2. After undoing the two knurled screws
(30), you can slide the table width ex-
tension into the opening.
3. Now  t the screw (A) back in the guide
tube. This serves as an end stop.
F_TS_2000_1_GB_SPK7.indb 26F_TS_2000_1_GB_SPK7.indb 26 04.06.2019 10:19:0104.06.2019 10:19:01
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex F-TS 2000-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex F-TS 2000-1 in the language / languages: English as an attachment in your email.

The manual is 3.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info