779785
16
Zoom out
Zoom in
Previous page
1/44
Next page
16
from the saw blade.
e) Only use the supplied push stick of
the manufacturer or one which has
been manufactured in accordance
with instructions. The push stick ensu-
res that your hand is kept at a su cient
distance from the saw blade.
f) Never use a damaged or partially
sawn push stick. If the push stick is
damaged, it could break, causing your
hand to come into contact with the saw
blade.
g) Do not perform your work “free-han-
ded”. Always use the parallel stop or
the miter stop to position and feed in
the workpiece. “Free-handed” means
using your hand to support or feed in
the workpiece with the parallel stop or
miter stop. Free-handed sawing leads
to misalignment, jamming and kick-
backs.
h) Never reach over or into a rotating
saw blade. Reaching for a workpiece
could lead to accidental contact with
the rotating saw blade.
i) Provide support for long and/or wide
workpieces behind and/or at the side
of the saw table, so that they stay
horizontal. Long and/or wide work-
pieces have a tendency to fall o at the
edge of the saw table; this leads to a
loss of control, the jamming of the saw
blade and kickbacks.
j) Feed the workpiece in smoothly. Do
not bend or twist the workpiece. If
the saw blade becomes jammed,
switch off the power tool immedia-
tely, pull out the power plug and
rectify the cause of the jam. If the saw
blade becomes jammed because of the
workpiece, this could cause a kickback
or cause the motor to block.
k) Do not remove the sawn material
while the saw is running. Sawn ma-
terial could become stuck between the
saw blade and the stop rail or in the
saw blade and cause your  ngers to be
drawn into the saw blade if you attempt
to remove it. Switch o the saw and
wait until the saw blade has come to a
standstill before removing the material.
l) For longitudinal cuts on workpieces
thinner than 2 mm, use an additional
parallel stop which has contact with
the table surface. Thin workpieces can
get wedged under the parallel stop and
cause kickback.
F_TS_2000_1_GB_SPK7.indb 16F_TS_2000_1_GB_SPK7.indb 16 04.06.2019 10:19:0004.06.2019 10:19:00
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex F-TS 2000-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex F-TS 2000-1 in the language / languages: English as an attachment in your email.

The manual is 3.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info