Manual Ferm WEM1035 (page 6 of 112) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510130

Zoom out

Zoom in

1/112

6 Ferm

space (free of iron powder, dust and paint).

• Place the welding appliance on a firm and flat

surface and at least 20 cm from the wall.

• Protect the welding appliance against rain and

strong sunlight.

The welding mask

Fig. 2

• Slide the handle on the welding mask until it

locks.

• Place the light glass (protective glass) in front

of the dark welding glass. Slide both glasses

in front of the opening.

• Make sure that the glasses are positioned so

that no (harmful) light can now penetrate the

opening.

• Replace the light protective glass when the

view of the workpiece becomes insufficient

during welding. Replacing the dark welding

glass is considerably more expensive than

replacing the light protective glass.

Fitting new electrodes

The electrode consists of a metal core enclosed

by a coating. At one end of the electrode the core

is not covered by the coating.

• Press the handle of the electrode holder

against

the spring.

• Place an electrode with uncoated end (± 2 cm)

in the electrode holder. Make sure that the

non-coated part makes good contact with the

metal part of the electrode holder (electrode

not pushed too far in the electrode holder).

• Release the handle of the grip. The electrode

is now fixed.

N.B! Do not allow the electrode to burn to

lengths shorter than ± 5 cm because of

overheating and/or the deformation of the

electrode holder. The burnt up electrode

will then be difficult to remove.

Removing used electrodes

Press the grip of the electrode holder against the

spring so that the burnt up electrode can fall from

the holder.

N.B! Do not remove the electrode from

the holder by hand. The electrode is very

hot!

N.B! Watch where the waste electrode

falls to prevent a fire hazard and possible

injury.

Installation

Fig. 4

Only an authorized electrician is allowed

to connect the correct plug to the welding

machine.

• Placetheblockingscrew(A)inthecorrect

position for 230V(4a) or 400V (4b). (See Fig. 4

a,b,c)

• Warning:Whentheswitchisonposition

“230V”, the wiring L, N and PE in the power

cord should be connected with the mains

power supply. When the switch is on position

“400V”, the wiring L1, L2 and PE in the power

cord should be connected with the mains

power supply. Above that a suitable fuse has

to be used.

4. Operating

Before use:

a. General information about electric arc welding

b. The electrode

c. Protective clothing

d. Face protection

e. Working environment

a. General information about electric arc

welding

The temperature of the arc amounts to approx.

7000° Celsius, so the end of the electrode and the

workpiece fuse. For as long as the arc is

maintained, the electrode will melt and supply the

necessary welding material to the parts to be

joined. The distance between the electrode and

the workpiece must be as short as possible

(approx. 1.5 - 4 mm) depending on the diameter

and type of electrode. The current needed for

welding is supplied by the welding appliance.

The power required by the welding appliance

depends on the work to be done.

Make sure that the electrodes are completely dry,

as moist electrodes cause problems. If the

electrode sticks to the workpiece during welding

your current intensity is set too low.

b. The electrode

• The electrode consists of a metal core

enclosed by a coating. The coating has the

most important purpose of protecting the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm WEM1035 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm WEM1035 Manual

Product: