510130

Ferm WEM1035 Manual

5
Zoom out
Zoom in
Previous page
1/112
Next page
EN
5
Ferm
• The slag to be chipped off is sometimes
glowing hot and can cause serious eye injuries
during removal. Always wear protective
goggles and gloves.
• Ultraviolet radiation can burn your skin during
welding. So always wear suitable protective
clothing.
• Your welding appliance is protected against
overloading. The welding appliance therefore
automatically switches off if it overloads. The
welding appliance automatically switches on
again after it has cooled sufficiently.
• During welding and cooling your workpiece
can deform due to stresses. Always bear this
in mind.
• Only the welding cables included in the
delivery kit may be used (Ø 10
mm
2
rubberized
welding cable).
• Special regulations apply to areas at risk of
fire or explosions.
• Welded connections that are exposed to high
stress and which must fulfill certain safety
requirements may only be carried out by
specially trained and certified welders. Some
examples are: Pressure vessels, slide rails,
tow couplings, etc.
• Important: Always connect the ground terminal
as close as possible to the weld spot in such a
way that the welding current can take the
shortest possible path from the electrode to
the ground terminal. Never connect the
ground terminal to the housing of the welding
device! Never connect the ground terminal to
grounded components that are located far
away from the workpiece, e.g., to a water pipe
in another corner of the room. Otherwise, the
protective conductor system of the room in
which you are welding could become
damaged.
• The fusing of the supply lines to the power
outlets must correspond to regulations (VDE
0100). Protective contact outlets may be fused
with a max of 16A (types and technical data:
RT14-20, Ø 10 x 38, AC 400 V 16A. IEC
60269. slow blow. Manufacturer: Chint) (fuses
or line-protection switches). Higher amperage
fuses can lead to burnt cables or fire damage
to the building.
Electrical safety
Switch off the machine at once if:
• There is a defect in the mains plug,
power cable or there is damage to the
cable.
•Defectiveswitch.
•Youseesmokeorsmellburnt
insulation.
Warning! Depending on the supply mains
conditions at the point of connection, the
welding power source may cause
interference to the supply to other
electricity users. If there is any doubt
about this question advice should be
sought from the electricity supply
authority.
• Make sure that the welding appliance and
electric wiring connections are properly made.
Any likelihood of electric shock can endanger
life.
• Always ensure good connections, both of the
electrode holder and the earth terminal.
• Do not allow electrical cables to be damaged
by pulling. Disconnect cables before you move
the welding appliance.
• Avoid contact with the electrically conductive
part of the welding appliance, the electrode
holder and the earth terminal.
• Always check that your mains voltage
corresponds to the value on the type plate of
the machine.
• With the replacement of cables or plugs:
Throw away old cables or plugs as soon as
they have been replaced by new ones.
Inserting a loose cable plug in a plug socket is
dangerous.
• For all welding appliances working on 230
Volts use at least 16 Ampere fusing
• When use is made of extension leads: Use
only an approved extension lead that is
suitable for the machine power. The cores
must have a diameter of at least 1.5 mm
2
. Roll
the cord fully out if the extension cord is on a
reel.
• Only allow qualified electricians to work on the
supply voltage end, e.g., on cables, plug-in
connectors, outlets, etc.
3. Mounting accessories
Make sure that the plug has been
removed from the plug socket during the
assembly of accessories.
Installation of the machine
• Install the welding appliance in a dry and clean
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm WEM1035 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm WEM1035 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info